As the title says.
Me for 1 and my 2 boys.
Type: Posts; User: Snafu
As the title says.
Me for 1 and my 2 boys.
How old is the 410 ? But for humane reasons no need to use solids just use at the most sg or bb size shot. Even shot size 1 or 2's would be plenty for humane reasons.
Bearing life span is a very difficult to answer. It depends on many factors, but I did my front bearings and they had just over 200,000k's on them. Now on where there made this is funny as my old man...
The Meopta line of scopes I have heard are good never actually looked through one thou. The Vmax's would be like dynamite on thin skin and the 150's should be good for deer.
I have only been on the...
The 270 Win is a good allrounder like the 2506, if the turrets only goto around 500m and you need to go further look into a 20MOA base. Another reason I like the PST's is the " ballistic reticle "...
I have been told Peter Turner in Guildford (03) 54734380 is excellent to deal with.
What you like to know Sooty.
I have found the Vortex Viper Pst's to be excellent scopes. Comparing them to the Razor, NF, Doctor etc the colour rendition isn't quite there but good enough I'm not...
Good to see there are a few hunters on here.
Myself usual 22RF, 22 Mag, Beretta 687S.
But my favourites are a ZKW-465 Brno 22 K-Hornet custom build with Vortex Viper PST 4-16x50, Rem 700 22-250...
Chicken has changed his design, slightly different to mine.
First thing LB how is it making it CB worse.
Icom 400 pro can be reprogrammed for 25w output and different frequencies technically need a license. A bit of searching and you will find out how.
Or a linear amp they come in various wattage...
Blocking the egr or removing it and removing it the intake butterfly is one of the best mods you can do for engine longevity.
I also have a Chicken tray on mine, the only thing was I had to modify it to fit around the dipstick tube. But makes life so much easier.
Mudski you really shouldn't let the oil drain over starter...
You will need to do a rear tail shaft flip with the slip joint at the gearbox end so the tail shaft has more clearance above the cross member when at full droop.
The gearbox output flange ( were the...
Advice before installing the uni's remove the caps and pump full of grease to remove all the air then put a bit of grease on the caps, then install. What can happen if you don't fill the uni's...
The king pin bearings run moly grease do to the limited movment these bearings do and the load they are under.
Spot on pretty much the same what I do after NS take the boy's to school then do some cleaning and coffee with her, pick the boy's up after school play with them and have around only 3-4 hours sleep....
To true I don't want to do more hours for less $$$ that's for sure.
I have tried to make plans for days off but for some reason or another nothing works out ( stuffed if I know ).
Just this...
Don't muck about with cheap filters personally I only use Donaldson filters.
I need advice guys.
This morning my wife told me to get another job. My roster is 4 ( 12 hour shift ) on and if you classify the morning I finish night shift its 5 days off before I go back.
I have...
In regards to coolant everytime I do a oil change I remove a litre or so and replace with fresh mixed 50:50 with demin water. So the coolant is getting constantly turned over so to speak running...
Bloody Aussie & Special Dave how things going with you guys ?
I hope all is ok.
SNAFU
Hi Dave
This will sound hypocritical.
From someone that has and is still suffering from depression for a number of years seeking help is the best way to go. Myself who thought I can fix this and...
K type thermocouple's are very common can either be used for digital or analog, depending on how they are made / materials depends if they measure temp from the minus's to hundreds oC or just...
The easiest way I have found to remove the needle roller is the remove the neddle rollers and cage. The from the other end using a long stanely flat blade proceed to tap it out.
Also don't forget...