OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

Search:

Type: Posts; User: cos

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    1,555

    Come apart by unscrew some M6 scew , head hex 10...

    Come apart by unscrew some M6 scew , head hex 10 . I install more than once , but never remove indicator and headlight , just fell the screw head with fingertips and used right tools ( articulated...
  2. Replies
    5
    Views
    1,353

    Use a tie-down strap with a ratchet, do a cross...

    Use a tie-down strap with a ratchet, do a cross tie from the axle to frame , compress springs a litlle ... move carefuly .
  3. Thread: MQ Wiring Diagram

    by cos
    Replies
    15
    Views
    14,590

    An splendid nothing ...

    An splendid nothing ...
  4. Thread: MQ Wiring Diagram

    by cos
    Replies
    15
    Views
    14,590

    I can't see diagram , is some wrong ?

    I can't see diagram , is some wrong ?
  5. Thread: MQ(260) glow plugs

    by cos
    Replies
    23
    Views
    23,165

    Check relays too .

    Check relays too .
  6. Replies
    3
    Views
    3,945

    Remove two M6 screw and using a longer M6 (must...

    Remove two M6 screw and using a longer M6 (must be a 10.9 screws , not a soft ones ) screws to bolt a piece of respectable solid , at least 14 mm thick flat iron with a central M12 screw you can...
  7. Thread: MQ(260) glow plugs

    by cos
    Replies
    23
    Views
    23,165

    I have the same engine and I think the original...

    I have the same engine and I think the original sistem must keept working especialy for postglow feature . Most common malfunctions is from a burnt contact points or burnt flexible wire inside...
  8. Thread: Uk 260

    by cos
    Replies
    15
    Views
    3,427

    Welcome to the forum , maybe can help in your...

    Welcome to the forum , maybe can help in your problems at 260 , I have a 206 too .
  9. Thread: Cv joint help

    by cos
    Replies
    4
    Views
    1,121

    Yes , same CV.

    Yes , same CV.
  10. Replies
    490
    Views
    197,407

    I'm a custom furniture maker , I work in my own ...

    I'm a custom furniture maker , I work in my own ( noisy ) whorkshop .
    Slowly going to be a fabricator of some custom agricultural suff - not ususal things ready to buy . Not too much furniture...
  11. Replies
    12
    Views
    3,267

    Welcome . Ceap fuel ... or no compromises...

    Welcome .
    Ceap fuel ... or no compromises .Great to own two .
  12. Thread: Hola, from Spain

    by cos
    Replies
    19
    Views
    4,649

    ... oh well , since you have a way , why not ....

    ... oh well , since you have a way , why not ....
  13. Replies
    9
    Views
    2,768

    A spring can't have same behaviour in time ( if...

    A spring can't have same behaviour in time ( if eventualy was identic with his oposite side ) ... from various resons ( roads , driver , weight even or not on the both side ) ...
    You can use a ...
  14. Thread: crank chewed out

    by cos
    Replies
    36
    Views
    6,943

    Nobody can be sure for this to answer .

    Nobody can be sure for this to answer .
  15. My be a little side offset , this can be a reason...

    My be a little side offset , this can be a reason .
  16. Thread: Hi All

    by cos
    Replies
    12
    Views
    2,711

    welcome to the forum .

    welcome to the forum .
  17. Thread: Introduction

    by cos
    Replies
    13
    Views
    2,944

    Welcome , can' help in any way ( since i'm...

    Welcome , can' help in any way ( since i'm european ) with you request but I admire you future trip plans .
  18. Replies
    7
    Views
    1,695

    For a 2.8 is a waaay to much . The IC is only...

    For a 2.8 is a waaay to much . The IC is only reason to not feed engine with engine oil an suprarev himself till a conectin rod break and engine rech his very final end .
  19. Thread: crank chewed out

    by cos
    Replies
    36
    Views
    6,943

    Welding is very posible , using a proper welding...

    Welding is very posible , using a proper welding rod ( in this case must be a high nikel content , is more another options ) .

    In any case , is a very last way to repair this problem .Better...
  20. Thread: Hola, from Spain

    by cos
    Replies
    19
    Views
    4,649

    Welcome , great pics !

    Welcome , great pics !
  21. Thread: Hello all

    by cos
    Replies
    16
    Views
    2,752

    Thank you .

    Thank you .
  22. Thread: Hello all

    by cos
    Replies
    16
    Views
    2,752

    Thanks for welcome , i'm not a member in ww...

    Thanks for welcome , i'm not a member in ww romania for simply reason of distance , is a good 500 km or so beetwen us . W wolwes ar in the montains , i'm at the very near Danube Delta . But ,...
  23. Replies
    1,371
    Views
    294,343

    Good question ...

    Good question ...
  24. Thread: crank chewed out

    by cos
    Replies
    36
    Views
    6,943

    What happend with you crankshaft ?

    What happend with you crankshaft ?
  25. Thread: Hello all

    by cos
    Replies
    16
    Views
    2,752

    Thanks all with all my respect . I will post...

    Thanks all with all my respect .

    I will post pics soon , i totaly agreed to my country is the most beautiful in the world ( ... but people from the same country don't care about this and no...
Results 1 to 25 of 36
Page 1 of 2 1 2