Thanks Craig, I will drain and refill as suggested.
Type: Posts; User: PeeBee
Thanks Craig, I will drain and refill as suggested.
No idea Craig. I seem to recall a thinner rather than heavier was the go - background drive into the hubs or something?
OK, good point, all other gears are fine, BD reckons the box only had 40,00 on it when the conversion was done so its now maybe 45,000 old. Or its another BD bullshit story and the box had 8 Million...
I have noticed that the 5th gear selection is at times notchy and am wondering if the bush in the top of th box is the culprit. Has anyone replaced the two plastic elements, how easy/time involved,...
Thanks Stropp, spent another big day on the barge, stuffing around and doing things once properly, 240V system now installed, double Makita 18V battery charger installed, on board Victron 240V...
More or less finished the POD electrics today, debating whether I stick with the breaker panel or just run have short extension leads instead to the other side of the POD - bit extravagant with the...
Wife flew to China today with one of my daughter to look at old pots or something, wasnt really listening, anyway cracked on with the sliders today between meetings and dealing with retards, made...
They are a very sexy looking bar. From my days working at Kaymar Eng, the requirment was to have the supplementary lights to cater for an 45 deg viewing block of the factory indicator/stop assy. It...
Yep, I get it, but NO, leave it as it is if you want the pump and pressure would be my recommendation.
I would run a pressure regulator limited to no more than 5psi. Anything more and the tank could split. Running pressure in a plastic tank is asking for problems.
Yep, but the increase in pressure only needs to be a poofteenth to generate massive velocity out the nozzle ( 5PSI across the total area of the tank is a massive discharge force.). What I dont like...
Dr Google says fires ok at Dalhousie outside of Nov to March due to fire hazard and must in permanent fire pits
John, I assume the tank has a breather in the cap? If not it will suck in and stock flowing with either a pump or gravity. A small hole , say 3- 5mm dia would be fine, you could screw in a pneumatic...
Good outcome, however I think you would achieve the same flow just letting the water run out the hose. Anyway its installed and working
Today I sorted out a coolant leak behind the S/C manifold, bloody utilux clips and such a range of clamps that do and don't tighten adequately. Ran the cables for the solar panels thru the pod wall,...
OK guys, I agree the platform has had some issues lately, all good, could not make sense of it after a full day in the Zoo with the primates.
I dont know what or who is screening these posts , but this is a post made TODAY and its been deleted or relegated to a non existent post today - WTF is the point of contributing if the filter...
Finally connected the electrical feed to the bank of lithium's in the pod, turned on the 10Kw inverter and plugged in the 240V 15amp lunchbox welder, ran it at 100amps for about 3 mins continuous and...
Here is the image I have tried to attach 2 Million times 88064
Crap it works now, or great work!
This is the new tapping wrench above the older 'still in service heavy duty wrench I made in the...
This is what I am getting also
OK, tried it again, not happening, I surrender, must be at my end.
Something strange going on, I have two posts today with images, both wont display, have erased the originals and re-attached, still not showing, will leave it to the guru's to sort.
Cannot get the .jpg images to display - anyone else having this issue? @AB
This brute arrived today. The original surviving HD tapping wrench is at the bottom. I like the extra leverage and everything is so much bigger and gruntier.
88037
Fourth box arrived today, thinking about a couple more for the rear seat as have the platform config already sorted.
88036