OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

Search:

Type: Posts; User: Bidja

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    6
    Views
    224

    Do not know the build of your starter motor, but...

    Do not know the build of your starter motor, but will throw this up.

    Solenoid maybe pulling in but contacts could be worn/eroded not allowing for good electrical contact. You say after a few...
  2. Replies
    456
    Views
    37,458

    Always miss your mates and more so when they have...

    Always miss your mates and more so when they have gone. Clunk, So hard mate_sometimes we think they are there, as just for a moment, but not to allow our fond memories to go..Jimmy Bidja RIP
  3. Replies
    10
    Views
    531

    Coltrain sent you a PM

    Coltrain sent you a PM
  4. Replies
    10
    Views
    531

    catch can _ Provent200 pre fuel filter _ look at...

    catch can _ Provent200
    pre fuel filter _ look at Waterwatch Not cheap though https://www.waterindiesel.com.au/product-page/nissan-patrol-3-0l-pre-2012...
  5. Replies
    456
    Views
    37,458

    MB These cones are so in the way. This might...

    MB These cones are so in the way. This might work depends where operated.

    Chockie had a "cone head" got smashed good time. Try alternative_T shirt
  6. Replies
    8
    Views
    495

    Asked about exhaust sounds to help determine if...

    Asked about exhaust sounds to help determine if you have a vac leak (hoses to solenoid/or VNT actuator), if vac problem it would prevent actuator from functioning correctly to control vanes and be...
  7. Replies
    11
    Views
    347

    Couple of more (Use FMIC these days): 1. As...

    Couple of more (Use FMIC these days):
    1. As mentioned, used same existing vert brkt adjacent to ABS but located CC fwd next to aux battery (Current CC install position is where large rotary switch...
  8. Replies
    11
    Views
    347

    My current install might suit ie: used an...

    My current install might suit ie: used an existing vertical plate brkt that comes off inner guard, adjacent to ABS (just fwd). Used 2x50mm pieces of angle(each approx 150mm long), mounted one angle...
  9. Replies
    11
    Views
    347

    Have done 3 different CC installs CRD GUIV_what...

    Have done 3 different CC installs CRD GUIV_what cooler and airbox are you going to end up with?
  10. Replies
    9,252
    Views
    815,633

    No worries Mark. Fitted a PDI FMIC...

    No worries Mark. Fitted a PDI FMIC (600x300x76mm):

    http://www.nissanpatrol.com.au/forums/showthread.php?45775-FMIC-Install-and-Suitable-Bull-Bar_08-GU-IV-CRD&p=792101#post792101

    Do not need...
  11. Replies
    9,252
    Views
    815,633

    Took her for a run up the mountains today, up to...

    Took her for a run up the mountains today, up to Lake Eucumbene to see how recent mods shaped up.
    FMIC, new fuel pump, bonnet louvers and running Tillix boost controller along with VNT vac solenoid...
  12. Replies
    456
    Views
    37,458

    Cheers MB mate, both really enjoyed the viewing. ...

    Cheers MB mate, both really enjoyed the viewing.

    Got hooked on watching the next "Last of the pure Dingo_Fraser Island. So many people get there these days, we went Fraser '85 mid winter 2wks...
  13. Replies
    9,252
    Views
    815,633

    So U are diversifying and getting into jam...

    So U are diversifying and getting into jam transportation....
  14. Replies
    12,614
    Views
    1,082,955

    Sticky: Feel for U Phil, trust they won't return it to...

    Feel for U Phil, trust they won't return it to the sender as the whole thing could get too confusing for them with a p/h.
  15. Replies
    12,614
    Views
    1,082,955

    Sticky: My morning toast will be late cause the PV solar...

    My morning toast will be late cause the PV solar sys will not wake an hour earlier...
  16. Replies
    33
    Views
    1,399

    Bonnet Louver Vent-Rear Facing No need for...

    Bonnet Louver Vent-Rear Facing

    No need for bonnet scoop with FMIC, so replaced large scoop with a rear facing louver panel I had made up from 1mm thick mild steel (O/A 700x600mm with louver...
  17. Replies
    5
    Views
    245

    As you were running the Diesel Smart 20psi...

    As you were running the Diesel Smart 20psi actuator, the diaghram would not compress spring until boost reached 20psi (would have caused limp). For stock ECU the actuator spring is to be 16psi max.
    ...
  18. Replies
    5
    Views
    245

    Simmon67, how are loading your engine up to...

    Simmon67, how are loading your engine up to determine your max boost 10-11 psi level (bypassing the VNT vac sol)?

    You have done the correct test to determine if you can make boost, bypassing boost...
  19. Replies
    9,252
    Views
    815,633

    Putting more holes in my bonnet and having fun...

    Putting more holes in my bonnet and having fun with it. Might be a bit cooler.
  20. Replies
    8
    Views
    495

    VNT actuator working properly ? @ idle the...

    VNT actuator working properly ?
    @ idle the actuator rod should be up(lever against stop), then (still @ idle) pull vac hose of at actuator and does rod drop down 10mm or so?

    Have you a scan...
  21. Replies
    5
    Views
    245

    Simon67 drop by the intro section say G'day tell...

    Simon67 drop by the intro section say G'day tell us a bit about yourself mate.
    http://www.nissanpatrol.com.au/forums/forumdisplay.php?2-Introductions


    Re: your boost issue:

    When you bypass...
  22. Certainly both would compliment each other and in...

    Certainly both would compliment each other and in time may become a reality for me. Majority of my off road driving is high country not over difficult but on occasion seeking out new fishing spots,...
  23. A bit of topic but related. I do not have...

    A bit of topic but related. I do not have either low range reduction gears or diff locker fitted. Would the reduction gear for low range application be the priority install of the two options...
  24. Did check it out, the guy certainly gives the pro...

    Did check it out, the guy certainly gives the pro locker a push and quite rightly so as the Elocker achieves positive lock (direction change) only after it overcomes the cam operation lag (bit...
  25. Cool, silent time here at moment so have not...

    Cool, silent time here at moment so have not watched video yet. Will do though.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4