OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

Search:

Type: Posts; User: garett

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    23
    Views
    9,862

    82077 been playing with the coilovers and had to...

    82077
    been playing with the coilovers and had to replace my esc, steering servo and i'm using a lipo battery ...
  2. Replies
    18
    Views
    904

    i put a 6 inch light bar under my spare tyre,...

    i put a 6 inch light bar under my spare tyre, worked well just need to be a little careful putting the spare back
  3. Replies
    22
    Views
    1,656

    been using a punch to turn bolts/screws sorta...

    been using a punch to turn bolts/screws sorta like the old cold chisel trick for nuts. i also have a removal kit that u drill a hole hammer a bar in then slide a nut onto the bar, works unlike...
  4. not sure if it helps much but there were 3...

    not sure if it helps much but there were 3 options for rear sway bar d bushes on GQ's ... different sizes. cant tell you if they are shaped different though
  5. Replies
    203
    Views
    26,847

    no idea... i've been fur-lowed so i dont even get...

    no idea... i've been fur-lowed so i dont even get to work ... bored out of my nutter. replaced the bushes in my rc car with bearings, played with the coil pretension and shock height. did the water...
  6. Replies
    203
    Views
    26,847

    well as i'm stuck inside ... missing my...

    well as i'm stuck inside ... missing my patrol.... don't see many of them here.
  7. Replies
    203
    Views
    26,847

    81177 my new toy while i'm stuck over here .

    81177
    my new toy while i'm stuck over here .
  8. my ford patrol / Nissan maverick goes alright,...

    my ford patrol / Nissan maverick goes alright, last time I drove it...
  9. Replies
    8
    Views
    2,649

    I run 33 10.5 15's... works fine been through...

    I run 33 10.5 15's... works fine been through sand mud rocks etc also only needed a small flare, and I didn't need to modify mud flaps with 2 inch lift.
  10. Replies
    6
    Views
    778

    well I took out the rear bearings at about 550...

    well I took out the rear bearings at about 550 000km... first time they were even looked at. only changed cos I went to disc's, new 2nd hand housing axles ect,
    on the 2nd or 3rd set at the front.
  11. Replies
    10
    Views
    958

    is the hose on the correct side of the cap ?

    is the hose on the correct side of the cap ?
  12. I saw this happen on a pathfinder... 2.5L I...

    I saw this happen on a pathfinder... 2.5L I think, ended up being a complete rebuild. bore was tapered and a new head,
  13. Thread: 1988 td42 gq

    by garett
    Replies
    2
    Views
    678

    yeah they seem to be getting hard to find a...

    yeah they seem to be getting hard to find a working one.
    I ended up getting one from I think it was a rb30, pulled the speedo out to put in my td42 cluster. everything but the speedo and odometer...
  14. Replies
    23
    Views
    9,862

    since this drive I removed the foam in the rear...

    since this drive I removed the foam in the rear tyres and will see if this improves it.
  15. Replies
    23
    Views
    9,862

    went for a drive/climb. 780687806978070

    went for a drive/climb.
    780687806978070
  16. Replies
    13,213
    Views
    1,372,140

    Sticky: looked at the car after someone drove it into a...

    looked at the car after someone drove it into a tree branch. checked a few other things, 2 leaky injectors a oil seep above the alt. and a broken exhaust shield. add it to the list I spose.
  17. Thread: Disc Machining

    by garett
    Replies
    16
    Views
    1,348

    personally id go with machining on the car. ...

    personally id go with machining on the car. machining should be much cheaper than new rotors. I had those rotors with Bendix pads on the wifes mazda 323, I got whinged at, it stopped too quick......
  18. Replies
    11
    Views
    870

    I used dba t2 4x4 survival on the gq with Bendix...

    I used dba t2 4x4 survival on the gq with Bendix hd. made a big difference but not as much as upgrading the rear to disc....
    I've been through mud water sand etc never had a problem except for the...
  19. Thread: e10

    by garett
    Replies
    6
    Views
    2,127

    I found it cheaper with my old carby to use 95...

    I found it cheaper with my old carby to use 95 over e10, strait out fuel cost vs amount burnt
    was told it would damage the rubber seals... only in the older cars most car since bout 2000 should be...
  20. Replies
    1,371
    Views
    180,721

    should check out the either direction roundabout...

    should check out the either direction roundabout thingy in hemal Hempstead.
    https://www.google.com/maps/@51.7462862,-0.4733119,136m/data=!3m1!1e3
  21. Replies
    1,371
    Views
    180,721

    mate some one should tell the poms about that. ...

    mate some one should tell the poms about that. they put multiple sets of lights on a roundabout.
  22. Replies
    7
    Views
    917

    it might not be that great but jaycar were...

    it might not be that great but jaycar were selling kits to add one to older cars without it, I know not as good as the factory one but.
    i'm not sure how its wired but it could be a number of things...
  23. Replies
    14,958
    Views
    1,482,490

    Sticky: enjoying a beer slushy

    enjoying a beer slushy
  24. Replies
    5
    Views
    828

    ahh that depends on the engine... if it calls for...

    ahh that depends on the engine... if it calls for synth than use the synth, running mineral in an engine that requires synth can cause problems. I found it depends on the engine which brand is...
  25. I picked up a 2nd hand set of extractors cost me...

    I picked up a 2nd hand set of extractors cost me 50 bucks, if you have the time they do come up for sale every so often
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4