OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

Search:

Type: Posts; User: mudski

Page 1 of 20 1 2 3 4

Search: Search took 0.12 seconds.

  1. Thread: MAF sensor

    by mudski
    Replies
    3
    Views
    55

    A wiring diagram isn't going to help if the maf...

    A wiring diagram isn't going to help if the maf is faulty. A new maf will fix it.
  2. Replies
    4
    Views
    102

    You will have better luck with next weeks...

    You will have better luck with next weeks tattslotto numbers than finding a definitive answer to what fixes the issue. In my case it was poorly balanced wheels. But I had to replace every bush under...
  3. I will be interesting to see the results if you...

    I will be interesting to see the results if you decide to change it.
  4. Nah Ive tried four different brand stats. Same...

    Nah Ive tried four different brand stats. Same result. currently using a Tridon Hi flow one as it seems to cool faster is the warmer months.
  5. Sticky: Yeah and the best bit is you dont have to make 25...

    Yeah and the best bit is you dont have to make 25 posts on the forum to get it anymore....
  6. If its struggling to reach 76c yeah I agree....

    If its struggling to reach 76c yeah I agree. Putting a higher rated stat in will just mean the water wont circulate until it reaches it spec'd opening temp. But in TD42 land. Who knows. It may help,...
  7. Replies
    4
    Views
    111

    Switch the auto hubs over from left to right and...

    Switch the auto hubs over from left to right and see if anything changes.
  8. Not sure. In my case, in the cold weather it will...

    Not sure. In my case, in the cold weather it will struggle to reach 76c. Unless I drive for hours on end to get the heat soak into the block. I took a day run up the snow a few weekends back and on...
  9. Nice work Mr MB. So whats your plan? Put the...

    Nice work Mr MB. So whats your plan? Put the coldest stat in and see? Better get a few spare stat housing gaskets and be careful of the long bolt that runs through the top and lower housing. These...
  10. Replies
    10
    Views
    469

    Well if you go too tight you will fell it when...

    Well if you go too tight you will fell it when spinning the wheel. So I'll tighten until then back it off a little so the wheel spins easily. But not too easy where it borderline becoming lose. If...
  11. Replies
    10
    Views
    469

    What I do is tighten them up until theres no...

    What I do is tighten them up until theres no movement other than rotational. Then go for a drive around a few streets then jack it up and recheck.
  12. Your wont have factory remote central locking....

    Your wont have factory remote central locking. So, i think, there wont be a control module. Its all controlled by the master switch, I believe. Their will be a way to do it. Using the new keyless...
  13. Get a quote from them, theres a few hours in...

    Get a quote from them, theres a few hours in this, it might get a bit exy. If your good with the spanners and have the time, you can do it yourself no issues. Like i said, take plenty of pics as you...
  14. I honestly can't remember if that will be easier...

    I honestly can't remember if that will be easier or not. Removing the entire intake is a big job. Get yourself a Gregory's manual, and/ or, download the pdf here. It will explain a lot for you. The...
  15. Replies
    15
    Views
    1,275

    Issue is for me too, I have zero motivation to do...

    Issue is for me too, I have zero motivation to do it outside.
  16. No. Unless they are physically broken, they will...

    No. Unless they are physically broken, they will be fine. If you do the job yourself, make sure you bleed the injectors properly by cracking the nut on each one and pumping the primer until the air...
  17. Replies
    15
    Views
    1,275

    Nice. I have so much that I need to do to mine,...

    Nice. I have so much that I need to do to mine, but having to remove the roof rack everytime to get it in the garage is a pain. So not much gets done.
  18. Replies
    4
    Views
    118

    Andy at DieselTec is good. Took my TD there and...

    Andy at DieselTec is good. Took my TD there and tuned it right. He's a bit of a character though, he comes across like he's no interested in talking, but he doesn't shut up. He seems to know his...
  19. Replies
    7
    Views
    150

    Welcome mate. Where in Melbourne are you living?

    Welcome mate. Where in Melbourne are you living?
  20. Sweet. Atleast you know 100% what it is. They are...

    Sweet. Atleast you know 100% what it is. They are a bit of a pain to remove and replace as you need to remove the injector lines but it doable...
  21. Replies
    3
    Views
    151

    The list is almost endless. Hopefully Bidja...

    The list is almost endless.
    Hopefully Bidja pipes up. He done pretty everything you can to his CRD.
  22. Oil vapours from the turbo. Remove the IC and see...

    Oil vapours from the turbo. Remove the IC and see anyway. Like I said if the bottom side of the IC has wet oil deposits, its leaking and needs to be changed. You turbo will be working overtime to...
  23. Ok another quick search. OEM part number...

    Ok another quick search. OEM part number 21200-51D02 is 82c.
    As for Tridon part numbers.TT228-180 is 82 deg and TT228-195 is 91 deg
  24. Is it the original intercooler? If so check the...

    Is it the original intercooler? If so check the underside of it for wet oil deposits. The original IC's are well known to leak and if you see oil on it, its leaking. Throw it out and replace it. This...
  25. Wouldn't that piss you off. Do HPD do the Adapter...

    Wouldn't that piss you off. Do HPD do the Adapter you need?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4