OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

Search:

Type: Posts; User: Dr Gary

Page 1 of 11 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    19
    Views
    13,705

    My ebay replacement lamps have been working for...

    My ebay replacement lamps have been working for more than 4 years. Basically need to get the wiring correct off the existing lights. Yes, you do need to make a loom to get side to side, but nothing...
  2. Thread: 2002- 2004 gu

    by Dr Gary
    Replies
    13
    Views
    649

    DI ran until the end of 2006. CRD hit the market...

    DI ran until the end of 2006. CRD hit the market in 2007. I have the 2006 DI.
    Had the joy of a grenade with my 2006 Di, but I am pretty sure I was over fueling--mods to MAF, turbo etc. I am now back...
  3. Replies
    37
    Views
    1,855

    Check your private messages

    Check your private messages
  4. Replies
    2
    Views
    276

    Glow plug working life

    Does anyone have information (not speculation) on the working life of glow plugs--3.0 direct injection.
    Either mine are losing performance, or the relay is dropping out too quickly.
    Missing for 3...
  5. Replies
    4
    Views
    308

    So with the knowledgeable responses I am...

    So with the knowledgeable responses I am satisfied that I have it about right. Thanks to all.
  6. Replies
    4
    Views
    308

    Expected cruising boost

    DDi 3.0 (not common rail)
    Does anyone know the expected unmodified boost pressure when cruising around 90 - 100 km/hr.
    Alternatively, what pressures are you experiencing??
    Seems I get between 9...
  7. Supercheap will sell you a good workshop manual...

    Supercheap will sell you a good workshop manual for <$50 and it has all the wiring etc for all models from around 1998 to 2008 and maybe beyond.
  8. Replies
    12
    Views
    782

    Endine number

    So I have my nicely painted replacement engine--black paint on the block. I can't seem to locate a stamped engine number. Maybe on a flat on the casting rear passenger side( is that left from the...
  9. Replies
    12
    Views
    782

    Finally saw sense in your comments and got a...

    Finally saw sense in your comments and got a complete rebuilt swap over, including new head. Also opted for a fuel system rebuilt pump, new injectors etc. Not cheap but probably due soon anyway. SMS...
  10. Replies
    12
    Views
    782

    The rebuild is similar $$'s to re-co motor. They...

    The rebuild is similar $$'s to re-co motor. They also fit a new head. I know the rebuilder and they are local. Time is not critical--except I am reduced to borrowing my wife's Territory :biggrin:...
  11. Replies
    12
    Views
    782

    OK so I now know the issue is the two front...

    OK so I now know the issue is the two front pistons are stuffed--not in the top but down the side. Really bad scoring of the bore in both cylinders. It looks like #2 has been hot, but I guess if a...
  12. Replies
    12
    Views
    782

    The head carries a camshaft that runs off the...

    The head carries a camshaft that runs off the timing chain at the top part of the front. That covers the drive to the camshaft, so needs to come off.

    I suspect I can get the front cover off, and...
  13. Replies
    12
    Views
    782

    Hi Hodge: Actually did the engine out water...

    Hi Hodge: Actually did the engine out water repair a few years back, just a slight bow in the steel plate behind the timing gear. $50 fix for $3K. This is no compression between #1 and #2.
  14. Replies
    12
    Views
    782

    Hi Mudski: you are probably correct but I have...

    Hi Mudski: you are probably correct but I have had too many birthdays to be rebuilding at this stage. Should have done it when I had the engine out to do the water leak.
  15. Replies
    12
    Views
    782

    Timing cover removal 2006 3.0DDi

    I have compression issues with #1 and 2 cylinders--both fail to hold compression. #3 and 4 are fine.
    Initial diagnosis says there is a blown head gasket between those two.
    Has anyone been...
  16. Replies
    2
    Views
    395

    The truck is in the shop and I suspect there is...

    The truck is in the shop and I suspect there is an issue with the existing turbo, hence the thought about a replacement.
  17. Replies
    2
    Views
    395

    Turbo and intercooler replacement

    Had a little issue with my GU 3.0 Di and I am considering replacing both turbo and intercooler.
    Is Garrett a good turbo replacement, or is there a better alternative??
    Are the eBay intercoolers...
  18. Replies
    14
    Views
    1,004

    A picture is worth a 1,000 words. Thanks for that.

    A picture is worth a 1,000 words. Thanks for that.
  19. Replies
    8
    Views
    503

    I think the crankcase is always under pressure...

    I think the crankcase is always under pressure when running, so removing the oil cap simply lets the built-up pressure out, fumes and all. When it comes out the normal crankcase vent, the Provent...
  20. Replies
    14
    Views
    1,004

    Thanks for the comments. Seems the common...

    Thanks for the comments. Seems the common solution here is hose and valve down the side.
    I did research Mann (the Provent maker) and they suggest either return oil to the sump, or vent the...
  21. Replies
    14
    Views
    1,004

    Provent oil drain

    Checking for a place to return oil from the Provent, I found the oil return pipe for the turbo connects to the "upper" sump.
    Has anyone used this connection for oil return?? and is this pipe under...
  22. Replies
    17
    Views
    813

    My Outback drawers came with a restraint point...

    My Outback drawers came with a restraint point bolted to a capture nut on the top/front of the left drawers. I took it out (no small kids ride here) and have no idea where I put it. Maybe take a look...
  23. Thread: Airbag recall

    by Dr Gary
    Replies
    62
    Views
    4,492

    My original replacement was 2016, now done again...

    My original replacement was 2016, now done again December 2018. Seems the replacements were bad as well.
  24. Thread: Gu ii

    by Dr Gary
    Replies
    8
    Views
    605

    I sold my GQ 4.2 with around 160,000k. Had a...

    I sold my GQ 4.2 with around 160,000k. Had a Denco turbo fitted, but I thought, as it was a few years old, I would just get a new car to see me out----really bad idea. My GU 3.0 Di works fine and has...
  25. Thread: Abs

    by Dr Gary
    Replies
    7
    Views
    620

    I have a 2006 ST-S 3.0 Di built September 2006....

    I have a 2006 ST-S 3.0 Di built September 2006. The extra "S" means it cost a little more, but has the ABS and Alcantara seat upholstery. From the brochure, they are the only differences. Best I can...
Results 1 to 25 of 269
Page 1 of 11 1 2 3 4