I'm after a set of good condition side steps for a 2003 GU wagon. I really only need the left side but willing to buy a set. I'm in Bathurst NSW so if I cant pick up you would need to courier or...
Type: Posts; User: tallman
I'm after a set of good condition side steps for a 2003 GU wagon. I really only need the left side but willing to buy a set. I'm in Bathurst NSW so if I cant pick up you would need to courier or...
Interested in Item #4 - Passenger side aluminum sidestep if it would suit a 2003 GU and you could freight/courier?
Are those steps for sale?
Got it worked out guys, shes off the vehicle, saw the other bolt on the inside of the engine block. So for further information to others 7 bolts all up, 3 up top near turbo, 3 down bottom at where...
Im wanting to install a EGT gauge in the patrol but first Im removing the dump pipe to install the fitting. Gotta say..that heat shield cam off in 30 sec and Ive never done one before...lol I just...
I would imagine that it would be hard to get these body molding off in one piece to be used over again. I snapped a rear one getting them off and any heat and they warp to buggery hence why I am...
Removed the side body moldings as they were cracked and starting to come off. Anyway they wont be going back on as they have had it so Ive been looking around for something to replace them with. As I...
Bought my kit from this mob. https://www.tillix.com.au/product/boost-control-kit-suit-nissan-patrol-zd30-di-crd/
This may answer your question.... https://itstillruns.com/air-intake-resonator-do-12156112.html
Do you own https://dawes-devices.com Checked out MTQ they can go jump..not paying $120 just for a Dawes valve, Im after the whole kit.
Fair enough mate, can you recommend someone at all?
Guys where can I get hold of a dawes and needle valve kit from(not a china clone), the fella that used to sell them on ebay is no longer selling them.
I just bought a GU 2003 Patrol and all I got with the car was 1 key no fobs at all..so went on ebay and bought 2 of these...
Anyone who is handy with a spanner can do this, piece of piss to do. Took me around 2-3 hours to do, that included removing the bullbar.
...
Dam exactly what Im looking for.
I bought a Safari snorkel for my dual fuel 4.5 Patrol and fitted it a few months back, quite a easy job actually, and funny enough no need for a balance pipe as it runs fine on both petrol and gas...
Anymore progress here??
Well think I found my answer...on another forum there was a fella doing same thing as me, he was told those washes(shims) are for the auto hubs only and to just use the outside groove for the cir...
I just found if I remove that copper washer the steel washer and the clip from the inside groove I can put it all together with new clip on the outside groove of the axle(first pic). The middle pic...
Tried to pull axle out a bit further but it hardly moves, maybe 1mm.
Hi MudRunnerTD, which seal are you referring to? the only seal I installed was at back of rotor, also I never touched a brass bush or the cv?
Need some help please... bought a set of these http://www.ebay.com/itm/181172550518?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT&rmvSB=true and I am having trouble fitting them...
I...
I picked up a set of these draws in November fitted them early December, look to be very solid and strong. Have a problem with drivers side wing being a bit to tight, hard to lock into place. Also...
Old thread I know but thought I would update it a little. The Roo Systems and Adventure Kings double swag which is the same swag just re-branded is made by Darche apparently, so quality should be...
Old thread but thought I would add my 2 cents..Contrary to popular belief having the snorkel facing backwards is not the "wrong way around", the first snorkel that was invented faced backwards and...