OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

Search:

Type: Posts; User: Deano2506

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    3,706

    Ideally the sway bars should sit flat to work...

    Ideally the sway bars should sit flat to work perfectly in all situations
  2. Replies
    7
    Views
    2,150

    Never had a problem with mine again after...

    Never had a problem with mine again after replacement mate.
    Do it properly, not cheaply and it'll be fine
  3. Thread: new boots

    by Deano2506
    Replies
    3
    Views
    1,913

    I've got the ko2s,very happy with them. Had them...

    I've got the ko2s,very happy with them.
    Had them for 1.5 years,can barely notice any ware on them yet.
    Good in the wet and decent off road too
  4. Replies
    3
    Views
    1,180

    You'll need them to be able to adjust the pump...

    You'll need them to be able to adjust the pump safely.
    Get the gauges then increase fuel 1/4 turn at a time until you see 550 Max going up a good hill with your foot into it.
  5. Replies
    3
    Views
    1,180

    Have you got a egt gauge and a boost gauge?

    Have you got a egt gauge and a boost gauge?
  6. G'day mate,I had the same problem. I bought a...

    G'day mate,I had the same problem.
    I bought a pair of new Chinese pumps with seals from ebay,only cost me about $20.
    I'm still using the factory pumps with the new seals,fixed the problem and that...
  7. No worries at all mate. If you Need any more...

    No worries at all mate.
    If you Need any more pics just ask
  8. Agreed mate. I think in early series 1's up to...

    Agreed mate.
    I think in early series 1's up to end of 91 only the St and ti's were colour coded and after then I think only dx were grey
  9. G'day again mate.on mine the lower silver/beige...

    G'day again mate.on mine the lower silver/beige comes up higher than yours but I think this answers your question.
    This is a factory paint job
  10. G'day mate,I've got the same colour gq,I can get...

    G'day mate,I've got the same colour gq,I can get you some pictures tomorrow.
    Can you put up a picture of exactly what section you want a picture of ?
  11. Replies
    12
    Views
    4,296

    I'd be looking at master cyl. Internal seal is...

    I'd be looking at master cyl.
    Internal seal is probably gone allowing fluid to leak back into reservoir with no external leaks
  12. Replies
    7
    Views
    2,150

    My head was beyond repair so had to get a new...

    My head was beyond repair so had to get a new one.
    Yours doesn't look like it's beyond repair,wont know untill it's been pulled apart and inspected though
  13. Replies
    7
    Views
    2,150

    She's about to drop the seat. I had it happen on...

    She's about to drop the seat.
    I had it happen on an sd33 years ago,my seat smashed into pieces and killed the head.a machine shop should be able to fix it
  14. Replies
    5
    Views
    1,141

    Have you tried nissan?

    Have you tried nissan?
  15. G'day mate,bit hard to point you to an area with...

    G'day mate,bit hard to point you to an area with the info you've given.
    Maybe you could post a video of the sound?
    They don't have centre bearing in tailshaft,just a slip joint.
    Good luck with it.
  16. Replies
    5
    Views
    1,329

    The factory gauges can be dodgy mate...usually...

    The factory gauges can be dodgy mate...usually bad sender unit.
    Put a mechanical gauge on it and check that
  17. Replies
    4
    Views
    1,284

    Looks like part of oil cap to me,i had a bit...

    Looks like part of oil cap to me,i had a bit break off too,looks just like that.
  18. Replies
    6
    Views
    1,681

    I've had a dayco in mine for 5 years now,it's...

    I've had a dayco in mine for 5 years now,it's been great.
    Think it cost me around $120 from memory.
  19. Replies
    8
    Views
    2,946

    Sounds like it has to be a vacuum leak somewhere....

    Sounds like it has to be a vacuum leak somewhere.
    So they're good for 1st 2 or 3 pumps ???
    Leak in vacuum tank maybe?
    You could disconnect at alternator or vacuum pump(depending on model),seal it...
  20. Handbrake adjustment is on the back of your...

    Handbrake adjustment is on the back of your gearbox as thats the handbrake.
    The other pic you have is the brake bias valve....don't fiddle with it
  21. Replies
    1
    Views
    2,372

    G'day mate.yes,it is just an o ring under that...

    G'day mate.yes,it is just an o ring under that plate.
    That might not be the leak though.
    Top cover is the usual spot,drips down and makes it look like it's the o ring.give it a good degrease and ...
  22. Replies
    6
    Views
    1,576

    Don't know if this is any help for you but the...

    Don't know if this is any help for you but the older sd33 and sd33t both have inline pumps and the sd33 has the butterfly in the inlet but the sd33t has the throttle going straight to the pump,it has...
  23. Thread: Depression

    by Deano2506
    Replies
    1,084
    Views
    449,272

    Sticky: So sorry to hear that mate. It's a hard slug...

    So sorry to hear that mate.
    It's a hard slug with the way things are in the "new world".
    Going back 5 weeks i was on my first cruise with the wife...we were on vayager,returned 18th march.it...
  24. Replies
    5
    Views
    2,903

    Just get some extremely dark tint on it. The...

    Just get some extremely dark tint on it.
    The rear side and barn door glass is classed as a cargo area,so it can be as dark as you want it and legal too
  25. Replies
    54
    Views
    37,052

    Best post I've seen on here in a long time.great...

    Best post I've seen on here in a long time.great looking work too.
    Keep up the updates mate
Results 1 to 25 of 125
Page 1 of 5 1 2 3 4