Going to be buying a turbo in the next week and am at a tipping point between my options so any feedback would be appreciated:
1988 TD42. off-road and touring, Looking to have a set up at around...
Type: Posts; User: The Negz
Going to be buying a turbo in the next week and am at a tipping point between my options so any feedback would be appreciated:
1988 TD42. off-road and touring, Looking to have a set up at around...
Thanks. I will try and find the part number on the trans
Just a quick Q about GQ Transmissions
The manual transmission in the GQ, do all transmissions have the same gear ratios for the TB TD and RD?
Just did a big trip and really noticed the Gap...
"Hadn't heard of the Sherpa before. Suspect you made a good choice."
Neither had I until I was tracking down 24V units. But the specs look good and so do their winches, big lbs and decent pull...
I was very impressed with the phone service, both for knowledge and technical data (I am a science and engineering teacher) and customer service.
The concept behind their compressor is to have high...
Thanks all for the advice, Boss had no PZ07 in stock and all the eBay listing where a bit jacked up. Also, boss highly suggests a receiver tank and with 2 weeks before I leave trying to find and fit...
I am putting in a call to Boss tomorrow to ask about the PX07 as a stand-alone compressor as it seems to flow the same as the ARB Single but is 100% duty. but for 500 its pretty close to the twin and...
Hello All,
1988 GQ Patrol Need a descent compressor for inflating 32" tyres
24V truck: So my selection of Compressors is limited. I was looking for an underhood mount with front and rear...
Hey All,
My neighbour has mounted GU Series 3 recovery points on a GQ. says 1 out of the 2 holes are there on each side and just drilled the extra hole.
I think the GU points would work best...
just have minimal castor correct bushes in it for a 2-3 inch lift.
Rear sway bar is in and I am installing a front. new springs ended up costing me 80 bucks ( sold the old ones for 250 plus black...
Called around to a few equippers and answered the 1st questions about shocks
3" shocks on a 2" lift is no issue and the shocks I have are only 8-12 mm longer than the "3 inch" shocks recommended.
Hello All, Looking for some advice on my suspension setup
1988 Safari Grandroad High Roof Touring Truck. TD42, 24V (2 batteries) Factory Bull Bar and PTO Winch, Fridge, 3 Draws, Aux Belly Tank,...
Hello,
Just re-introducing myself as it is coming up with me not having any post when I have a few threads, no worries
Near Bribie Island with a 88 Safari Grandroad.
General camping/touring...
Sorry 2nd picture
73875
I have a pressure switch (looks like a standard oil pressure swtich) located behind the alternator. where does it go? It was not hooked up when I bought the truck.
88 Safari Grandroad 24V
...
ok some more research from my end. the "torque setting" on the lock nut is at 490nm. using the torque force design equation for a lubricated surface come out to a clamping force of...
The work shop manual says this about install.
"Install spacer over axle shaft and press axle shaft into inner
race of wheel bearing."
Hello, 88 Safari. rear discs.
The issue I am having is the bearing I ordered seem to be a fraction to small in Inside Diametre. The axle is 45mm. The bearing ID is 44.8-44.9 which indicates a...
nothing drastic maybe 20-30mm. luckly the seals where really bad on one side and the axle is still dirty so I am going to try that.
Will post result and some photos
Sorry forgot to mention 1988 Safari Wagon, Coil sprung. and I am pretty sure the longest axle is the passangers.
rear doing the rear wheel bearings, did not pay attention to which side the short axle goes to. Any help would be great.
Cheers
G'Day gange
My shocks on my stock 88 are completely done, I am looking for a set of used shocks as I am lifting it but not for a bit and don't want to buy shocks twice.
I am just north of brissy....
Hello,
So when rebuilding my PTO winch I damaged the Manual Locking Hub. Everything works but it is extremely hard to turn needing pliers.
Being an older Y60 the hub is one that takes a transfer...
Just a quick question as I am pretty sure I know the answer, but I can be an idoit so let check.
Whats the yellow range bar on the early model Y60 yellow dash indicate. redline is obvious, yellow...
Hello,
I am looking for a single manual locking hub off a GQ Patrol, it needs to be the one with the extra gear on the axle. It is going to be used for a PTO winch repair.
I am just north of...