OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

Search:

Page 1 of 40 1 2 3 4

Search: Search took 1.00 seconds.

  1. Replies
    44
    Views
    12,964

    I found that an old camera tripod leg is great...

    I found that an old camera tripod leg is great for the times you need an adjustable pole to press the pedal to check the stop lights or trailer socket when you are alone.
  2. Replies
    6
    Views
    117

    Same here, in the Nanny State.

    Same here, in the Nanny State.
  3. Thread: Pic Fails.

    by mudnut
    Replies
    24
    Views
    401

    One way of flushing your hard earned cash.

    One way of flushing your hard earned cash.
  4. Thread: Pic Fails.

    by mudnut
    Replies
    24
    Views
    401

    Pic Fails.

    Here's your chance to post those wonderfully disastrous picture fails.

    My first offering: A photo bomb instigated by a territorial wattlebird.
  5. Replies
    5
    Views
    208

    ROH used to be good quality rims. I bought a Trak...

    ROH used to be good quality rims. I bought a Trak 2 rim as a spare. It started rusting around the cut outs within a couple of months. Got another under warranty, and it was rusty within 12 months....
  6. Replies
    8
    Views
    211

    "Thar she blows!" Has it got the Nissan...

    "Thar she blows!"

    Has it got the Nissan Anti-Detonation System installed (NADS) If so then maybe consider it. Go NADS!

    Talk to the owner about what has been done to the grenade, er, engine and...
  7. Replies
    1
    Views
    69

    Welcome to the forum. This is from a GU manual so...

    Welcome to the forum. This is from a GU manual so it might be different. But it is a starting point.
  8. Replies
    4,932
    Views
    504,678

    Finally scored a series 2 RB30 crankshaft. Got a...

    Finally scored a series 2 RB30 crankshaft. Got a few other goodies off the engine too. Now I can get the old engine rebuilt and it can be a spare.
  9. Replies
    15
    Views
    393

    I used cable for years, but the cable kinked when...

    I used cable for years, but the cable kinked when doing a job so when money became available I switched. Life is so much easier using dyneema.
  10. Replies
    15
    Views
    393

    How dyneema rope soft shackles are made.

    https://www.youtube.com/watch?v=TBTiYf-9Hys
  11. Replies
    6
    Views
    288

    Welcome to the forum. Usually smoke on start up...

    Welcome to the forum. Usually smoke on start up means worn valve guides and / or valve seals.

    What is the compression on each cylinder? Do a compression test. If it is low, then squirt a smidgen...
  12. Replies
    10
    Views
    209

    Happy birthday, Darren.

    Happy birthday, Darren.
  13. Replies
    44
    Views
    12,964

    Couldn't get Easy Outs because of Covid Lockdown,...

    Couldn't get Easy Outs because of Covid Lockdown, so I used an Allen key that was just slightly larger than the hole drilled through the broken bolt. Just make sure you hold the key straight as you...
  14. Replies
    9,948
    Views
    1,093,094

    They have so many quirks and so much potential,...

    They have so many quirks and so much potential, they're worth studying. I've been researching to build one with an RB34 stroker kit with NA pistons for a bit of low down grunt, giving a bit more...
  15. Replies
    9,948
    Views
    1,093,094

    Thanks, Mudski, but I can't take credit for this....

    Thanks, Mudski, but I can't take credit for this. The engine builder thought of it, I just swapped out the components.
  16. Replies
    9,948
    Views
    1,093,094

    Ever since the rebuild, the lifters have been...

    Ever since the rebuild, the lifters have been noisy. Swapped the machined lifter carriers/cradles out. This carrier is 20 thou thinner, than standard so the hydraulic lifter are able to cope with the...
  17. Replies
    13,448
    Views
    1,455,233

    Sticky: Long-winded Political discussions :)

    Long-winded Political discussions :)
  18. Replies
    6
    Views
    181

    The book says to really tighten the bearing to...

    The book says to really tighten the bearing to 145ftlbs - 167nm. Rotate the hub a few times in both directions. Loosen the nut to zero, then tighten to sweet bugger all, (3-5nm.) Turn the wheel again...
  19. Replies
    6
    Views
    181

    40ftlb or 56nm according to the manual.

    40ftlb or 56nm according to the manual.
  20. Thread: Termites

    by mudnut
    Replies
    21
    Views
    1,857

    HAAA HAAAA HAAAA best spammer fail, ever.

    HAAA HAAAA HAAAA best spammer fail, ever.
  21. Replies
    13,448
    Views
    1,455,233

    Sticky: Read in the local rag, that the driver of one of...

    Read in the local rag, that the driver of one of the vehicles in the fatal crash at Mt Richmond had drugs in his system. FFS!!
  22. Replies
    6
    Views
    232

    They are in the GQ service manual you can...

    They are in the GQ service manual you can download from this forum. At page BF 58 to 59
  23. Replies
    133
    Views
    19,259

    After a 3/4 hour lesson I spent an hour or two...

    After a 3/4 hour lesson I spent an hour or two testing out all the functions I was taught.

    I got a few good snaps but this one was the best.

    The sigma lens was set at 500mm. The Shutter at...
  24. Replies
    18
    Views
    432

    Depends on how much time you have. In the...

    Depends on how much time you have. In the morning, all the oil that will drain away has done so just after the engine shut down. The length of time that the oil drains out cold is extended. If it is...
  25. Replies
    5
    Views
    275

    I have a GU 4.3 diff centre in my GQ so I assume...

    I have a GU 4.3 diff centre in my GQ so I assume the housings must be the same. You might have to mark a tyre and the drive shaft with chalk. With the a jack under the diff, rotate the tyre and count...
Results 1 to 25 of 1000
Page 1 of 40 1 2 3 4