Search:

All good mate. I worked that out also. A series of pump, crank, pump, crank for about 30 seconds and she kicked. A few more rounds of crank and pump and she started. I kept pumping for a few...

I just dropped in another pump and it started up, with no NATS headache. :)

I will be there taking the ARB bar off so will take photos. Putting the standard bar back on, I guess cable ties and duct tape is ok for trade ins. :tongue:

The bar I am buying is coming off a GU that is getting traded, so I will need to swap my bar over. Does anything get chopped off when fitting an ARB rear bar?

Thanks threedogs, i will try Barry.

Sent from my GT-I9507 using Tapatalk

I have just bought a used ARB rear bar for my GU and before I started to fit it I wanted to read the fitment instructions. I called ARB and they refused to send me a copy of the fitment instructions...

Thanks for the hot tip re priming mudski. Should i crack the injector lines while cranking for the first start to help it prime?

Are there any differences in the ZD30DDI pumps?

Sent from my...

I am about to replace the Injector pump on my 2001 ZD30 and I was wondering if I will need to have the NATS reprogrammed to match the new injector pump? Isn't that where it immobilises the engine or...

My glow plugs were not working when I got mine and I only found out on the first cold morning and it smoked and didn't want to start. Turned out to be that they had been over tightened and the...

Shock Absorber boot?

I dont think it is a wrecker number, I have never seen one so neat. :p I thought it may have been a sign of a rebuild, but maybe all early GQs had it. Is there a way to find out how old a motor is...

I was changing the thermostat which turned out to be a bigger job after a bolt snapped and I had to remove more bits to get the broken bit out then I found this tattooed on the front cover of the...

97_gq_lwb, any chance you can post up a pick of your dump pipe? I am thinking of using the same manifold and am wondering where the dump pipe will fit without heaps of bends and how much clearance it...

Thanks nissannewby. I was thinking the same. I am planning on 12-14psi boost, so a 16G would be the way to go. I would much rather the boost come on sooner then later.

Has anyone used one of...

I want to fit a turbo to my TD42.

I would like to compare these 3 almost identical turbos which have a different compressor wheel, 16G, 18G and 20G. They are all listed for a TD42. I am...

I got a similar problem with my GU, the drivers door locks and does not unlock even though I can hear it trying to . I have to use the key on the pass side as no doors open and force the drivers...

Mine has nuts welded on, so you just put the bolts back in from below.

Oops, I did Killer not Killa.

Thanks, I googled and it only found forum post, none had a number.

Thanks Mate. I should stop asking how much, it keeps going up. :)

I can adapt the harnesses and whatever. I will give them a call to see if I can buy the bits and assemble it myself. Do you have...

I thought I read someone post that the KKK harness was something like $800? I can do all the wiring if that is all that is needed, but the adaption of the sensors is the unknown bit ie, water temp,...

Do all the ignition lights go out without a tacho signal? I would have thought something would need to be fed into somewhere keep it happy. Did you unplug the ECU?

Killer Kustom Kables do make a...

Also looking at the flow rate in the main tank filler neck seems to confirm the same rate.

Yeah I was thinking that the sub would transfer more over the course of using a full main tank. My Sub was still reading over the full mark when the light came on.

I think the sub pump runs for...

The light just came on, orange circle to the left of the E. I turned the sub on and it went out after 10 seconds. Any one know how much fuel is left when it turns on?