Would recon as part of wheel rim new manufacture production lot acceptance, a random sample quantity would be subjected to a spin up balance compliance test.
Recently also was experiencing 80-85...
Type: Posts; User: Bidja
Would recon as part of wheel rim new manufacture production lot acceptance, a random sample quantity would be subjected to a spin up balance compliance test.
Recently also was experiencing 80-85...
No worries Mark. Fitted a PDI FMIC (600x300x76mm):
http://www.nissanpatrol.com.au/forums/showthread.php?45775-FMIC-Install-and-Suitable-Bull-Bar_08-GU-IV-CRD&p=792101#post792101
Do not need...
Took her for a run up the mountains today, up to Lake Eucumbene to see how recent mods shaped up.
FMIC, new fuel pump, bonnet louvers and running Tillix boost controller along with VNT vac solenoid...
So U are diversifying and getting into jam transportation....
Putting more holes in my bonnet and having fun with it. Might be a bit cooler.
Yeah it all went through its first ever car wash (10yrs now) the other day and also used engine degreaser to help track down fuel pump leak. I live down a 5 km dirt road but must say certainly avoid...
Finished install of Cooma Diesel_WaterWatch inline water trap with alarm prior to install of new fuel pump.
https://www.waterindiesel.com.au/howwaterwatchworks
0-TJ-0 Just spent last hr looking thru posts for this air box and cannot find it. It was a single post on this forum, the guy stating he had one for sale as he was now going a different...
John if you like, I could get in touch with the bloke that makes them and get an email address for you?
Would PM you the details.
IMO the airbox is of good design. As I mentioned earlier your duct assy from airbox to turbo would fit up well. Only need 3" x 90° bend to connect up to A/box and possible adjust for length.
If...
mudski yeah, I also thinking it was a northern hemisphere thingo.
threedogs Worth checking this out mate_good flow. I currently use this airbox ($365 posted) that uses a K&N 9" pod filter_KNRE-0870 (approx $100).
Box comes in two lengths 300mm (ZD) and 340mm...
threedogs Yep will work well and the stock MAF flanged pipe section (3") could have flange removed and coupled up to airbox outlet. Pic of what I had with round A/B (Fabwitz Industries) and what I...
threedogs, I had one similar to this fitted to my GU CRD. Did work well, good for 200hp, but do not like the way the inlet flow is directed at 90° to the centre of the filter side face. Restriction...
Couple of weeks back had brkt failure on Berklee 3" sys (2nd section), failed at right angle bend of section fixing brkt as excessive induced stress resulting from hole out of alignment with G/Box...
mudski thought you may have increased the strength of the brkt by welding some increased thickness plate on the non critical face of them. Just a thought mate
Installed new radiator header tank, ordered from Patrolapart on Monday, arrived yesterday, was a long week and now installed (all good).
Leaned on old tank overflow spout up the bush last...
Thought I would put back in the positive pressure actuator (CRD) last night and with a bit of boot the VDO boost gauge went off scale at 30psi and could hold it there easily. Think something wrong...
Yeah I lost the E-Clip off the turbo actuator rod to lever pin the other day, even had some fishing line attached to it but it twanged out of the noose. No where to be found and all I could buy was a...
Completed install of 4" Airbox and snorkel. Also had to re position CC and Dual Aux battery charge select switch(also changed type) as needed more real estate.
Also wrap dump pipe and went past...
How did you do wrap "burn in"?
Have read to "burn in" at eng idle, bring up to op temp and let idle for further 15min. Did yours smoke much(not mine)? Think mine needs to be driven and get some...
Dump wrap and heat shield
Part of my induction upgrade to 4"(snorkel/airbox), I removed the Dump pipe, replaced turbo to exhaust gasket, applied wrap, fitted up a heat shield and applied thermal...
Took a hacksaw blade (body saw) to the GU guard and opened up a hole to receive the 4" recessed snorkel. Yet to be fix in place.
You did not connect up wrong polarity when measuring current and stuff the meter fuze?
Modules in parallel?
The 3 days wetting a line down the beach sounds a good time. Do enjoy walking along looking for gutters and casting some ganged pillies out after salmon. Been a while...
Today, been cleaning out...