Hi, where its always been in the outlet pipe from the IC to the throttle body, as I already had fitted the boost and EGT gauges, sometime ago
BUrto
Type: Posts; User: Burto
Hi, where its always been in the outlet pipe from the IC to the throttle body, as I already had fitted the boost and EGT gauges, sometime ago
BUrto
Hi all, well all is good now, blocked the ports on the boost control solenoid, as thought no effect, still 5psi boost max and high EGT, checked damper air passes through both ways so all good there,...
Will try that tomorrow and let you all know if that was successful, a very big thank you to you both for taking the time to assist.
Burto
HI, am pretty sure that the damper valve is the right way around, ports A, B and C on the solenoid are open to atmosphere, the needle valve is connected to the top port on the resonator as in Chez...
Thanks, I had thought that I had the needle valve wound out to far and so was bleeding off too much vacuum, so closed the needle valve and went for another road test, but with no improvement,
...
Yep , measured the spring then stretched about 3mm, no difference, dismantled valve ball free and clean, out of ideas, will go back to standard setup, will return dawes and needle valve and they can...
Thanks, would have replied sooner but just ahd a small blackout, the valve was advertised as being sold with the stronger spring so that you would not need to stretch it,, used Chaz 's instructions...
Hi there, purchased dawes/needle valve on ebay, fitted following instructions from 3bar racing, adjusted needle valve, and went for a run, high EGT and boost of 5-7PSI, wound dawes valve in to...
Thanks mate, have removed injectors, fitting new ones with reco motor, your reply was most helpful,
Burto
Hello, replacing the injectors after having them serviced, my Ellery manual does not specify a torque figure, can anyone help.
Thanks
Burto
Good evening, does anyone have the tightening torque specs for the engine to transmission bolts for a Y61 ZD30 to 5 speed box, my Ellery manual doesn't specify.
Thanks in anticipation
Burto
Thanks, thats the problem, my longest adapter has the hex hitting the head before the thread is engaged, the adapter needs to have a fair length of travel before the hex hits the head say around...
Good evening all
Have compression gauge with snap on fitting, looking for the adapter for compression test on ZD30 through the glow plug hole.
Having no luck here abouts, local repco guy chasing...
Thanks Threedogs, provent is fitted, but little or no oil in it.
Provent was checked on the Monday when checked engine before the trip, and MAF cleaned.
Thanks for the response have sent PM this morning, will certainly look at this option.
BUrto
Well have started the strip and inspection, looks like may have dodged a bullet.
All intake hoses, intercooler and swirl valve have liquid engine oil in them, not burnt oil but good ordinary engine...
Thanks Rusty for your response, will probably strip it down to head off to assess any damage, then drop the sump and do a in chassis overhaul, if there is no significant damage or wear. Will get head...
HI all,
Thought I would add what happened, in case it may provide someone else with some info for the future.
Vehicle is a GU III built Dec 2002, manual with the famous ZD30 engine, it has 301700...
Thanks for your reply, Hodge much appreciated. Looks like Nissan has struck again, probably the only motor in the world that requires the gearbox to be removed to repair a leaking sump for example....
Hi there, well it looks like the fuse finally went off, running with miss, lots of smoke, no rattles thank heavens. Question do you really have to remove the transmission in order to remove the upper...
Dual battery set up, using 150 amp, Projecta, this runs at 100AMP continuous with 150amp peak, as Nissan alternator is a 90 amp alternator. The fused positive terminals are to prevent the dipstick...
Here is a photo of my gauge pod, from left, oil pressure, water temp, voltmeter for 2 batteries, selected by switch on dash, Boost and EGT gauges, all wiring fitted between dash and screen and down...
My drawers, test to see if photo was uploaded. It Works, see I didn't waste 2 hours, tg its raining
Burto
Thanks, found the paper clip, browsed photos on my computer, selected 2 photos, up, uploaded 2 photos, they didn't appear in my test message, where they went I don't know , spent too much time on...
Thanks for the response growler, I can see "go advanced" in the quick reply but it doesn't appear in the
post new thread',
Regards
Burto