OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

Search:

Type: Posts; User: Dr Gary

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    11
    Views
    759

    Flushed the system, radiator was checked and...

    Flushed the system, radiator was checked and really full of crud. Best solution was to replace it, which I did. Water pump "seemed" ok, but replaced as it was cheaper with the radiator out.
    Because...
  2. Replies
    11
    Views
    759

    Seems like I have two major issues 1) the water...

    Seems like I have two major issues 1) the water pump/viscose fan is suspect and 2) The radiator is 18 years old, so likely degraded inside.
    Replacing the radiator seems better value than cleaning,...
  3. Replies
    11
    Views
    759

    factory, but heating creates other issues as well...

    factory, but heating creates other issues as well as indicated temp. Actually loses a LOT of power. Following Mudski's list plus others so we shall see.
  4. Replies
    11
    Views
    759

    Getting the whole cooling system flushed (not...

    Getting the whole cooling system flushed (not DIY), viscose fan "seems" ok.
    Electric fan is ok, but no way to check if the ECU is actually switching it on other than when the engine is over heated....
  5. Replies
    11
    Views
    759

    Over heating under load ZD30 DDi

    My patrol overheated towing the boat , so much that engine stopped. The thermostat seemed to be stuck so replaced that.
    Same issue with overheating now.
    Complete engine replacement about 100k ago....
  6. Replies
    5
    Views
    1,259

    So I got the HPD hi flow. I will try that first....

    So I got the HPD hi flow. I will try that first. If needed I will get the hi flow lid.
    Thanks for the first hand information.
    Report back on outcome in the next couple of weeks.
  7. Replies
    5
    Views
    1,259

    Limp mode 3.0 Di

    I have taken my GU back to (almost) standard. Only engine bits: exhaust plate and catch can.
    I get a limp after a few minutes at 110 km/hr, no issues at 100 or lower.
    Remedy is to back off for 1...
  8. Replies
    2
    Views
    1,703

    Same problem I think. It seems easier to bend the...

    Same problem I think. It seems easier to bend the AC pipe when removing and refitting the engine. There is a mount bracket on the pipe, and a threaded hole in the side of the engine. Sure it should...
  9. Replies
    2
    Views
    1,703

    AC pipe routing

    I have just replaced the engine in my 2006 GU 3.0 Di.
    Unfortunately the mechanic moved the upper AC pipe, and when the engine went in, it was left hanging outside the air in pipe.
    It should be...
  10. Replies
    2
    Views
    597

    Hi "Rusty" I will wait on TD. Thanks for the clue

    Hi "Rusty" I will wait on TD. Thanks for the clue
  11. Replies
    2
    Views
    597

    Extended seat slide

    Hey guys
    Has anyone found seat slides that move the seat further back??
    How about height adjustment?
    I have standard factory seats and my son has now grown to the point he no longer fits--steering...
  12. Replies
    20
    Views
    5,049

    Large Metric studs have a number on the head,...

    Large Metric studs have a number on the head, denoting bolt strength, small have geometric code. US studs have slashes radiating from the centre, more means stronger.
  13. Replies
    0
    Views
    800

    Retiring from long distance travel

    I have a bit of gear for our longer trips and no longer needed. Includes 58 litre water tank and diesel tank, rear window protector, recovery tracks, winch extension, high lift jack etc,
    Tanks were...
  14. Replies
    8
    Views
    5,409

    Make it GOOO

    Just bolt on a Denco (or similar) turbo and it will go well and long. Did that with my old Maverick and it went fairly rapidly
  15. Replies
    19
    Views
    23,011

    My ebay replacement lamps have been working for...

    My ebay replacement lamps have been working for more than 4 years. Basically need to get the wiring correct off the existing lights. Yes, you do need to make a loom to get side to side, but nothing...
  16. Thread: 2002- 2004 gu

    by Dr Gary
    Replies
    13
    Views
    2,948

    DI ran until the end of 2006. CRD hit the market...

    DI ran until the end of 2006. CRD hit the market in 2007. I have the 2006 DI.
    Had the joy of a grenade with my 2006 Di, but I am pretty sure I was over fueling--mods to MAF, turbo etc. I am now back...
  17. Replies
    37
    Views
    11,257

    Check your private messages

    Check your private messages
  18. Replies
    2
    Views
    1,315

    Glow plug working life

    Does anyone have information (not speculation) on the working life of glow plugs--3.0 direct injection.
    Either mine are losing performance, or the relay is dropping out too quickly.
    Missing for 3...
  19. Replies
    4
    Views
    1,377

    So with the knowledgeable responses I am...

    So with the knowledgeable responses I am satisfied that I have it about right. Thanks to all.
  20. Replies
    4
    Views
    1,377

    Expected cruising boost

    DDi 3.0 (not common rail)
    Does anyone know the expected unmodified boost pressure when cruising around 90 - 100 km/hr.
    Alternatively, what pressures are you experiencing??
    Seems I get between 9...
  21. Supercheap will sell you a good workshop manual...

    Supercheap will sell you a good workshop manual for <$50 and it has all the wiring etc for all models from around 1998 to 2008 and maybe beyond.
  22. Replies
    12
    Views
    7,029

    Endine number

    So I have my nicely painted replacement engine--black paint on the block. I can't seem to locate a stamped engine number. Maybe on a flat on the casting rear passenger side( is that left from the...
  23. Replies
    12
    Views
    7,029

    Finally saw sense in your comments and got a...

    Finally saw sense in your comments and got a complete rebuilt swap over, including new head. Also opted for a fuel system rebuilt pump, new injectors etc. Not cheap but probably due soon anyway. SMS...
  24. Replies
    12
    Views
    7,029

    The rebuild is similar $$'s to re-co motor. They...

    The rebuild is similar $$'s to re-co motor. They also fit a new head. I know the rebuilder and they are local. Time is not critical--except I am reduced to borrowing my wife's Territory :biggrin:...
  25. Replies
    12
    Views
    7,029

    OK so I now know the issue is the two front...

    OK so I now know the issue is the two front pistons are stuffed--not in the top but down the side. Really bad scoring of the bore in both cylinders. It looks like #2 has been hot, but I guess if a...
Results 1 to 25 of 283
Page 1 of 12 1 2 3 4