I don't know the specs but there must exist a listing somewhere. I selected it because its used by a lot of people building hotrods and looking to clean up the engine bay. I would assume it would be...
Type: Posts; User: PeeBee
I don't know the specs but there must exist a listing somewhere. I selected it because its used by a lot of people building hotrods and looking to clean up the engine bay. I would assume it would be...
Are you referring to the Astra electric unit I carry as an emerg breakdown device? I am sure it will be fine. I cant see a need for 12L/min thru the power steering system anyway, but no doubt there...
Finger gotta itchy today after 2 weeks in a nightmare project stage so bought a Marks 4x4 hydro booster to go over the Willwoods. Expect a significant braking upgrade moving forward. The barge is...
Just a Harrop 2300 running the 16psi pulley. I would love the twin turbo feed like on the Banks test Motor, but frankly this engine isn't built for that kind of HP. The Banks engine runs twin turbo's...
No lag at all, hit the peddle and it takes off all the way to the redline if need be. I drive it fairly gently to be honest, keeping an eye on the egts and the fuel flowrate, which is quite brutal at...
Sorry to hear about your loss Ralph. Where did you end up sourcing the two wire sensor from? I found a supplier in China however it was a major drama getting the items - took months to arrive.
Second diesel heater leaking, clearly from the flange construction, not the barbs, changed the hoses and clamps and 15 secs after starting the engine the heater starts weeping at the joint. I have...
Lets hope so, how is your journey proceeding?
OK, took the beast out today for a 2hr squirt. A/C decided to give up the ghost, so have to get that checked out, maybe a gas issue. water Meth system drops the EGT's by around 40 - 50 deg it seems...
Water Meth tank installed and hooked up yesterday. All working as it should, hard to tell if any difference idling in the driveway, even with application setpoint on 100% of the time. Will see how...
Yeah, a 5T hoist is going into the shed at Wiseleigh. i have sort of finished under the car excepting the final shut off valve - I have bought some fuel line clamps for this so hope the amount of...
OK, completed the bracket above, what a total details nightmare. Getting the configuration to operate on a crazy offset took hours, but happy with it now, rewelded using the right rods and cleaned up...
OK, fiddling around yesterday, and after speaking with Bullet S/C they dont have a fast idle setup, so knocked up this one as the template. 6 hrs in the making, doesn't look like it but its sort of...
Taking it out for a spin either tomorrow or Friday, looks like it's fixed, better be!!!!
Krikit belt tensioner arrived today, tested the belt after speaking with the gates engineer about an auto tensioner value for the belt. A table was supplied, attached below which may be of value to...
I have been having issues with belt squeal since the beginning of the vee belt to 8 rib multi vee conversion belt drive. mudski put me onto a tool to measure the actual belt tension, which is another...
New passenger side rocker cover, 2 rocker assy's and gasket sealant on the way from WA - thats the limit of support - bit disappointing, but its better than nothin'. Appears today the leaks were...
Simply should not be the journey .This has been a nightmare from start to now, and its continuing.
Matt, the two worst are on the exhaust valves of 4 and 5, followed by minor bends mostly on the drivers side bank. i cant be too specific due to not taking enough attention as the bits were...
Blame game zone Darren. They have tried to shift blame onto my swapping out the timing chain for gears, then the key in the camshaft has failed and you need to strip the front of the engine down to...
Head gaskets blown on both banks, no 4 and 5 cylinders, 8 bent pushrods. Brunswick swap the head over on brand new turbo motors to change the inlet manifold port alignment, or so they say, so they...
Brunswick finally got back to me about the mount. yes, its splayed a bit 'but not as bad as they have seen in the past' - like how is that level of engineering comment to put a client at ease? -...
Brunswick finally got back to me about the mount. yes, its splayed a bit 'but not as bad as they have seen in the past' - like how is that level of engineering comment to put a client at ease? -...
Thanks Rossco, few other changes like new bearing sleeve for the bigger bolt, another $100, cut down the sleeve bolster head and changed the socket head cap screw to a button head and increased the...
Some time ago, like 600klm ago I suffered a mounting plate failure due to 2 bolts failing in tension on the 8 rib belt drive. I was assured by both Brunswick Diesel and Bullet performance this was...