OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

Search:

Type: Posts; User: nissannewby

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds.

  1. Davies Craig. 80-120lpm pumps. Flow is king with...

    Davies Craig. 80-120lpm pumps. Flow is king with w2a. I would be using the unit that is 25mm lines.

    The last w2a I setup had 1" lines and a Davies Craig 120lpm pump running flat out all the time....
  2. Replies
    196
    Views
    6,570

    There are ways to neaten it up a lot. Throw a PLC...

    There are ways to neaten it up a lot. Throw a PLC and basic screen in and you can run say like 1 can bus cable to the rear to a slave that then can switch on accessories. This kind of stuff is cool...
  3. UFI would be the only pumps I would use...

    UFI would be the only pumps I would use currently. They are constantly getting better at them with the r&d they do. I don't believe there is much difference between their 200hp 11mm or 200hp 12mm....
  4. It's just speculation lol. Both the Patrol and...

    It's just speculation lol.

    Both the Patrol and LandCruiser are at the end of their model runs. They are typically roughly a 10yr cycle. Apart from drawing the y61 out. So we should soon be due for...
  5. It is just an interim face lift will only be a...

    It is just an interim face lift will only be a short production while they are finalising the Y63 model 😋
  6. Replies
    151
    Views
    19,311

    Well the big girl is gone. She went to its new...

    Well the big girl is gone. She went to its new home today.

    Bring on the Y63!
  7. Replies
    9,252
    Views
    815,878

    Filled it with fuel and Washed it. Someone is...

    Filled it with fuel and Washed it. Someone is interested enough they want to put a deposit on it. So the big girl might be gone this week 😔
  8. Replies
    1,937
    Views
    193,127

    The old time traveller Groening at it again.

    The old time traveller Groening at it again.
  9. Around 92 degrees is the sweet spot for...

    Around 92 degrees is the sweet spot for performance
  10. Replies
    8
    Views
    312

    There are loose fasteners on the floor. Some look...

    There are loose fasteners on the floor. Some look to be the shock bush,washer and nut. These need to be installed.....
  11. Replies
    13
    Views
    582

    There is a connector on the bottom of the...

    There is a connector on the bottom of the injector pump on the td42ti engine. It will throw the engine light if there is a problem or its disconnected. Being towards the bottom of the engine they can...
  12. Replies
    196
    Views
    6,570

    The high pressure line will always be the smaller...

    The high pressure line will always be the smaller one. Everything after the steering box should be larger returning to the reservoir with basically no restriction. A cooler helps in that with a temp...
  13. All front Panhard rods have a curve in them...

    All front Panhard rods have a curve in them whether it be GQ or gu. Is the rear one straight?
  14. Replies
    151
    Views
    19,311

    Might hang out until the Y63 comes out....

    Might hang out until the Y63 comes out....
  15. Replies
    151
    Views
    19,311

    Yeah all is fine. Just priorities have shifted so...

    Yeah all is fine. Just priorities have shifted so selling up quite a bit of gear. I will hopefully own another one day.
  16. Replies
    151
    Views
    19,311

    We'll unfortunately I am selling another patrol....

    We'll unfortunately I am selling another patrol. I have really struggled holding onto these vehicles but such is life. Here is a link to the ad if anyone is interested. Will be sad to see it go. It's...
  17. Replies
    196
    Views
    6,570

    Yeah there is just to much flow returning to that...

    Yeah there is just to much flow returning to that little reservoir but it is only a thought. I know BD are fantastic are supplying secondhand crap
  18. Replies
    196
    Views
    6,570

    A standard shaft seal can usually only deal with...

    A standard shaft seal can usually only deal with very little pressure like 30psi or less. Unless a high pressure shaft seal is used. So the hose clamps will still hold on way after there is enough...
  19. Replies
    21
    Views
    780

    This guy is not far from my house. I have sat in...

    This guy is not far from my house. I have sat in these seats and spoken to him about a set for the 62. Basically your imagination is the limit for this guy. He had plenty of different styles and...
  20. Replies
    196
    Views
    6,570

    I don't want to seem like a prick but are you...

    I don't want to seem like a prick but are you 100% it's plumbed up correctly? To blow the shaft seal means you are pressurising the case somehow. The shaft seal should basically never see pressure...
  21. 255351LB5A That's the part number. There are...

    255351LB5A

    That's the part number. There are plenty of places online or as above nizzbits. The stealerships will charge you a mint for one. Can be had for under $50 from the middle east
  22. Replies
    163
    Views
    15,735

    Exedy Safari Tuff HD, UFI Clutch or NPC viper...

    Exedy Safari Tuff HD, UFI Clutch or NPC viper clutch. The first 2 I would recommend lightening the flywheel and balancing the mass. The NPC comes with a nice light flywheel and should be balanced.
  23. Replies
    196
    Views
    6,570

    Small ports I think are used when EGR was fitted...

    Small ports I think are used when EGR was fitted hence being black. Non EGR intake manifolds just don't have a port so it gets blanked off. I could be wrong here.

    The small canisters. The one in...
  24. Replies
    9,252
    Views
    815,878

    There is a bolt with a sealing washer on it...

    There is a bolt with a sealing washer on it inside the reservoir that holds the reservoir to the pump. These can leak when they get old and also if the bolt is a little lose. You coukd try nip it up...
  25. If what you say is true and you dont go over...

    If what you say is true and you dont go over relief then you could also use a slightly smaller motor to increase winch speed as well. You currently have just over 900nm available with you current...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4