OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

Search:

Type: Posts; User: PeeBee

Page 1 of 20 1 2 3 4

Search: Search took 0.17 seconds; generated 17 minute(s) ago.

  1. I have just gone thru a similar issue, not the...

    I have just gone thru a similar issue, not the same connections, however if you go to a dedicated a/c shop instead of an auto elec you might get a better result. My local a/c shop is absolutely...
  2. Replies
    4,804
    Views
    413,231

    Seems like cargo net focus could well start...

    Seems like cargo net focus could well start becoming a PLOD focus, so following MB lead, picked this one up today, not cheap but less than the $242 fine, plus 'whatever' they find as they comb over...
  3. Replies
    9,504
    Views
    918,608

    Tracked down a water leak on the new W2A circuit,...

    Tracked down a water leak on the new W2A circuit, slightly loose hose clamp but at 20psi the water was leaking out. Started into the second row seat platforms using old seat frames - will weld them...
  4. Poll: Yes 70mm2 welding cable. Its going to eat that...

    Yes 70mm2 welding cable. Its going to eat that application for sure, no problem. The duty rating of the cable should be on the outer sheath, and you can buy it by the meter. I have my jumper leads...
  5. Poll: Could be with AB by now, MB is a bit far away at...

    Could be with AB by now, MB is a bit far away at the moment as you probably know!!! Total Tools will probably have that welding cable as well.
  6. Poll: Looks like Licola has a chance of happening I...

    Looks like Licola has a chance of happening I think
  7. Replies
    530
    Views
    56,289

    Bad news Ross. Did you get the tree down though?...

    Bad news Ross. Did you get the tree down though? I am a little surprised at the failure as the bolts should not have been taking much load - they are more positional than in tension, the load in...
  8. Get a sopping wet tea towel and do a small weld...

    Get a sopping wet tea towel and do a small weld and quench the area immediately. I have done this with success many times, Just keep the weld zone small and absolutely quickly apply the teatowel to...
  9. Replies
    9,504
    Views
    918,608

    Propped the roofrack up one side at a time,...

    Propped the roofrack up one side at a time, replaced the rubber 'U' piece under the support rail in the roof gutter, cleaned the gutter out, doused it with rust converter for good measure - Nhoward...
  10. Replies
    14,514
    Views
    1,313,909

    Sticky: My wife wanted me to buy one, so it was easiest...

    My wife wanted me to buy one, so it was easiest to do that than resist.

    Last Subaru I had was in 1976, could not kill it as a young hoon driver. They are from a heavy engineering background so I...
  11. Replies
    304
    Views
    16,466

    OK, been thinking about this issue of the air...

    OK, been thinking about this issue of the air temp readings and doing some research. I believe the probe used in the airstream is incorrectly configured for air, its a probe configured for liquid -...
  12. Replies
    304
    Views
    16,466

    OK, the results are in, but not completely...

    OK, the results are in, but not completely accurate.

    The system was gassed up today and took the vehicle for a 100klm spin down the freeway and back home. Ambient temps were cool - 13 degC.
    ...
  13. Replies
    14,514
    Views
    1,313,909

    Sticky: Congrats Nicco, what are you doing?

    Congrats Nicco, what are you doing?
  14. Replies
    14,514
    Views
    1,313,909

    Sticky: Picked up the new Outback, drove the BMW down to...

    Picked up the new Outback, drove the BMW down to the dealer - bloody thing was running like a swiss watch - unlike its behaviour in previous weeks - reckon it knew something was up and it was trying...
  15. Thread: Air Ducting

    by PeeBee
    Replies
    15
    Views
    475

    Good point. I only addressed the air inlet

    Good point. I only addressed the air inlet
  16. Thread: Air Ducting

    by PeeBee
    Replies
    15
    Views
    475

    looks pretty close to a 45 deg tube bend - you...

    looks pretty close to a 45 deg tube bend - you could contact Geordie stainless in Melb - buy a grade 304 elbow, probably cost you $20 plus shipping then go from there with silicone sleeves and hose...
  17. Replies
    9,504
    Views
    918,608

    Agree Darren, good look, however my need was a...

    Agree Darren, good look, however my need was a little different. I have a lot of gear mounted on the barrier, so wanted to cover it up, plus I can't see out the rear of the vehicle anyway, so use the...
  18. Thread: Ex telstra

    by PeeBee
    Replies
    6
    Views
    206

    Cuppa is you man I believe for this

    Cuppa is you man I believe for this
  19. Replies
    304
    Views
    16,466

    OK, almost there, just have to put a/c...

    OK, almost there, just have to put a/c refrigerant into it and its done. Hooked up the tank, pump and power, hoses double insulated, pump flows at 41LPM, draws 19.8amps and pressure in system...
  20. Replies
    14,514
    Views
    1,313,909

    Sticky: Its a totally different drive to the545i BMW I...

    Its a totally different drive to the545i BMW I had, obvious downgrade in power, but feels solid and its quiet, which is surprising for a 'flat 6' engine. Anyway, another long term happy association I...
  21. Replies
    14,514
    Views
    1,313,909

    Sticky: Been hearing everywhere that now is the time to...

    Been hearing everywhere that now is the time to buy a new car, and I can attest to that. Picked up a 2 month old, 2020 Subaru Outback 3.6R with 2000 kilometres on it, optioned up for the Subaru exec...
  22. Replies
    304
    Views
    16,466

    Yeah, well $495 for a pair of plates that will...

    Yeah, well $495 for a pair of plates that will see the light of day 6 times a year is a bit 'off the menu' right now. I think the TAADIS is the winner though.
  23. Replies
    304
    Views
    16,466

    Thank You Men for your kind thoughts. Tardis not...

    Thank You Men for your kind thoughts. Tardis not avail for number plate, just checked
  24. Replies
    23
    Views
    1,731

    You are amazing, brilliant work, top stuff

    You are amazing, brilliant work, top stuff
  25. Replies
    304
    Views
    16,466

    OK, I don't exactly know how much it weighs, but...

    OK, I don't exactly know how much it weighs, but its been over the scales at 3320 and 3940kg. The 3320kg was for the engineering brake test/GVM upgrade and the 3940 was in semi battle ready config....
Results 1 to 25 of 497
Page 1 of 20 1 2 3 4