OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

Search:

Page 1 of 2 1 2

Search: Search took 1.00 seconds.

  1. Replies
    7
    Views
    300

    I had a boost pressure line that wasn't tight...

    I had a boost pressure line that wasn't tight from the intercooler to the boost pressure sender. The sender barb was thinner than the hose and let high pressure air out. It was whistling like a...
  2. Replies
    7
    Views
    300

    Check your turbo pipes are tight on the turbo....

    Check your turbo pipes are tight on the turbo. Had this one a while back, similar symptoms.
    Hard to track at idle. Only manifests at revs, was a lucky guess on mine.
  3. Replies
    7
    Views
    300

    Replace or repair the IC first I think then...

    Replace or repair the IC first I think then reassess. Other than this the exhaust manifold has possible warped or cracked.
  4. Replies
    7
    Views
    300

    Not sure mate, unless the crack has suddenly...

    Not sure mate, unless the crack has suddenly gotten bigger somewhere.

    That was just my first guess as I remember when our work car 3L had a crack on the IC. The performance wasn't that overly down...
  5. Replies
    7
    Views
    300

    I'm sure you've done this but have you had a good...

    I'm sure you've done this but have you had a good inspection of the intercooler for any little cracks, etc?
  6. Replies
    38
    Views
    1,792

    Apparently the earthquake has caused 10 million...

    Apparently the earthquake has caused 10 million dollars improvement to Frankston! :D

    Haha I can't talk, if only you knew the suburb I live in!

    84342
  7. Replies
    9
    Views
    541

    Do the rear wheels first then bias valve, then...

    Do the rear wheels first then bias valve, then the fronts.


    Sent from my iPhone using Tapatalk
  8. Thread: ARB Rear bar

    by 0-TJ-0
    Replies
    10
    Views
    1,488

    Just through Google, I searched gu ARB rear bar...

    Just through Google, I searched gu ARB rear bar install or something.
  9. Thread: ARB Rear bar

    by 0-TJ-0
    Replies
    10
    Views
    1,488

    Maybe this will help? Or maybe they won't....

    Maybe this will help?

    Or maybe they won't. They're the fitting instructions for the bar but don't show a whole lot.

    Might be of some use. Parts list shows 10 nyloc m6 nuts holding them on so I...
  10. Thread: ARB Rear bar

    by PeeBee
    Replies
    10
    Views
    1,488

    Sorry Brad, I don't. There is bound to be someone...

    Sorry Brad, I don't. There is bound to be someone pop up here with the answer. Give it a couple of days them simply re-post with a 'bump' after the last post. Sounds to me like they are using a bolt...
  11. Thread: ARB Rear bar

    by PeeBee
    Replies
    10
    Views
    1,488

    Is there a nut or bolt head on the underside of...

    Is there a nut or bolt head on the underside of the pivot point? I am sure you could get an answer from ARB. Looking at the 'thin/skinny' top plate I am guessing the pivot is bolted in. The top face...
  12. Replies
    12
    Views
    960

    RED from switch to Pressure switch DK BLU from...

    RED from switch to Pressure switch
    DK BLU from Pressure switch to relay
    RED WHT from relay to Compressor
    BLK WHT negative battery to compressor
    ...
  13. Replies
    12
    Views
    960

    So in that drawing the RED is coming from the...

    So in that drawing the RED is coming from the switch pin 3 (positive from carling switch to pressure switch).

    DK BLU goes from Pressure switch too Relay. Switched relay, relay turns on...
  14. Replies
    12
    Views
    960

    Red is positive from switch pin 3. DK BLU then...

    Red is positive from switch pin 3. DK BLU then goes from pressure switch to relay and is also a positive.

    Your positive from battery to fuse, then to Pin 2 on ARB Switch and 30 on your relay.
  15. Replies
    12
    Views
    960

    Hi mate, not sure why yoy have drawn a buss bar...

    Hi mate, not sure why yoy have drawn a buss bar but assume that is your relay or something. The pressure switch is tapped into the positive side of the supply. I would tap it in between the fuse and...
  16. Replies
    2
    Views
    313

    Measured stock (OEM) Torx M4 x 0.7mm pitch...

    Measured stock (OEM) Torx M4 x 0.7mm pitch (pitch best guess with vernier) out of CRD MAF stock housing. Effective length thread 10mm / overall length under head 12mm (stainless steel would be...
  17. Replies
    6
    Views
    1,234

    Yeah I have a dodgy tendon in my right shoulder...

    Yeah I have a dodgy tendon in my right shoulder so I have to do it left handed otherwise I get a false reading when torquing the hub nut up. :D If you heard the disticnt change in noise. I think you...
  18. Replies
    6
    Views
    1,234

    If you are unsure there is really only one way to...

    If you are unsure there is really only one way to reassure yourself & that is to pull the wheel off & re-check. When knocking in bearings, at least by the method I was taught. Have the hub on a good...
  19. Replies
    6
    Views
    1,234

    If the bearings weren't on far enough I doubt you...

    If the bearings weren't on far enough I doubt you would be able to do up the hub nut. Plus they only go in so far then stop against the raised section were the hub seal runs. Im not sure if 150ftlb...
  20. Replies
    4
    Views
    725

    Have a look at this video from bigguwesty...

    Have a look at this video from bigguwesty (Kallen) hangs around on the forum here

    www.youtube.com/watch?v=7tQziIey884.

    It is for Tllix install but same principles apply.

    Kallen help me...
  21. Replies
    4
    Views
    725

    Your vacuum take off is the" hard: steel stand...

    Your vacuum take off is the" hard: steel stand pipe that is located at front of eng near alternator. Use existing vac line (if in good condition) from this stand pipe, leave plastic damper in place...
  22. Thread: G'day everyone

    by Bigcol
    Replies
    6
    Views
    700

    welcome to the forum mate

    welcome to the forum mate
  23. Thread: G'day everyone

    by AB
    Replies
    6
    Views
    700

    Welcome to the forum mate and feel free to ask...

    Welcome to the forum mate and feel free to ask any questions.
  24. Thread: G'day everyone

    by Dhuck
    Replies
    6
    Views
    700

    Welcome to the forum mate

    Welcome to the forum mate
  25. Replies
    6
    Views
    700

    Welcome to the forum mate .

    Welcome to the forum mate .
Results 1 to 25 of 27
Page 1 of 2 1 2