OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

Search:

Type: Posts; User: Bidja

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    14,887
    Views
    1,459,040

    Sticky: Had 4 hrs straight sleep last, nodded off @...

    Had 4 hrs straight sleep last, nodded off @ approx 3 am had to wake up at 7:30 to take my steroids (Dexmethsone 40mg _10 tablet each morning for 4 days_now 3rd day). Keeps you awake /disturbed sleep...
  2. Replies
    2
    Views
    80

    Not sure how you will go for a further warranty...

    Not sure how you will go for a further warranty claim_can only try.

    IMO, if the exhaust manifold was badly warped, suggest a new replacement manifold be fitted and use inconel studs_if stock were...
  3. Thread: Memes Thread

    by Bidja
    Replies
    1,960
    Views
    246,681

    The way it is going. "Nature" will sort it ...

    The way it is going. "Nature" will sort it

    Have even started wearing gumboots again after sooooo long (memories of another time and place down south).
  4. Replies
    14,887
    Views
    1,459,040

    Sticky: The old Mobilco slasher did not let me down...

    The old Mobilco slasher did not let me down (second pull fired up)_gets into it (Kohler 6 1/4 hp side valve old timer m/c 1960s).
    Started cleaning up garden for the start of veg season.
    Surprised...
  5. Replies
    583
    Views
    41,242

    Good that you have observed some improvement...

    Good that you have observed some improvement Mark.

    In line with what PeeBee stated, checked my CRD fan blades_ would be lucky to covered 50% by the cowl skirt and radial tip clearance is nom...
  6. Replies
    583
    Views
    41,242

    Mark, have you thought of increasing depth of fan...

    Mark, have you thought of increasing depth of fan cowl, most likely pull more air. looking good
  7. Replies
    14,887
    Views
    1,459,040

    Sticky: mudski cruising ok mostly Mark. Been keeping low...

    mudski cruising ok mostly Mark. Been keeping low like most. Not so bad living out of town plenty to do. No cases in our shire, surprising considering Hume hwy passes thru and a bit of a haul for...
  8. Replies
    26
    Views
    1,244

    Could not resist swag memories of my good old...

    Could not resist swag memories of my good old mate Jimmy Bidja_this bag will do along side mum(Red).
  9. Replies
    14,887
    Views
    1,459,040

    Sticky: Only wet a line three time since all this COVID...

    Only wet a line three time since all this COVID started.

    Will finish my tank repairs today and have packed my mobile platform swag and box of artificial bugs.

    To the mountains after the...
  10. Replies
    13,072
    Views
    1,350,581

    Sticky: And still doing it for you (not good after all...

    And still doing it for you (not good after all the stuffing around) and sometimes not worth paying someone to look at. Don't think we got 5 yrs from last one. Guess just a bit hard to choose and...
  11. Replies
    13,072
    Views
    1,350,581

    Sticky: Have you tried unplugging for 10 minutes...

    Have you tried unplugging for 10 minutes (disconnecting pwr) forced reset of computer?

    Worked with my reverse cycle A/C after pwr surge.

    Maybe flush water thru where soap goes in / clean lint...
  12. The two batteries (ie: 2 separate loads/different...

    The two batteries (ie: 2 separate loads/different chg profiles) are isolated from each other via their individual MPPT controller. IMO_Should work fine(no common loads be connected in parallel to...
  13. Thread: Weekend projects

    by Bidja
    Replies
    53
    Views
    1,950

    Looking a bit of all right Rossco_top job mate,...

    Looking a bit of all right Rossco_top job mate, now for the Lichen starter rock.
  14. Clutch Engagement Adjustment_Good pedal height off floor now (08 GU IV)

    Thought I would share my successful clutch pedal height adjustment experience, required for install of 4 Terrain Ultimate ER2 clutch/SMF).

    12 months ago, replaced worn OEM Clutch/DMF (170,000kms)...
  15. Replies
    14
    Views
    984

    X2 ARB with MB aux tray(old family GU touring...

    X2 ARB with MB aux tray(old family GU touring truckster), be same me (adjacent to CRD Alternator). Handles many corrugations, our home road is full with them, does the job well (180,000 ks since...
  16. Replies
    2
    Views
    106

    Measured stock (OEM) Torx M4 x 0.7mm pitch...

    Measured stock (OEM) Torx M4 x 0.7mm pitch (pitch best guess with vernier) out of CRD MAF stock housing. Effective length thread 10mm / overall length under head 12mm (stainless steel would be...
  17. Replies
    18
    Views
    525

    more valves like thumbs as well_just need to...

    more valves like thumbs as well_just need to decide which way to install and turn. Get VNT vanes to open more gradually low down for more air after initial turbine spin up (higher MAF lower MAP).
  18. Replies
    18
    Views
    525

    The one I bought for exhaust end (3 holes) is no...

    The one I bought for exhaust end (3 holes) is no longer available. This one would be fine: ...
  19. Replies
    18
    Views
    525

    Will look up purchase detail on pc and let u know...

    Will look up purchase detail on pc and let u know . It has 3 stud holes exhaust plate and 2 holes or slots for inlet side
  20. Replies
    18
    Views
    525

    Stock is good to work with but can be costly and...

    Stock is good to work with but can be costly and time consuming sorting the wheat from the chaff. Had to learn as I went (never stop I guess).

    IMO opinion hold off on ECU remap for a while,...
  21. Replies
    18
    Views
    525

    Do you have any gauges installed as good to...

    Do you have any gauges installed as good to monitor changes as mods come into play.

    Is eng stock, any mods to date?

    In addition to blocking EGR, as mentioned you can disable the swirl valve...
  22. Replies
    18
    Views
    525

    Dhuck I agree with nipagu7 the best option...

    Dhuck I agree with nipagu7 the best option upfront is to get a ECU remap which if done well will turn the EGR fuction off and technically it is not then required to physically use the EGR blanking...
  23. Thanks Andy, EFT sent via copper today. Back on...

    Thanks Andy, EFT sent via copper today. Back on track.

    Good to put the subscription link (detail) in Thread Title or first post (new start for 2020 maybe or amend this title).
  24. Thread: ZD30 not power

    by Bidja
    Replies
    2
    Views
    185

    Assuming it is not fitted with positive pressure...

    Assuming it is not fitted with positive pressure actuator.

    Check vnt actuator on turbo. At idle the actuator rod / arm should be all the way up so lever is against vane limit stop screw, check...
  25. Thread: Weekend projects

    by Bidja
    Replies
    53
    Views
    1,950

    Neat looking retaining wall coming together there...

    Neat looking retaining wall coming together there Rossco, some serious lifting and must be glad for the pincher helpers haha.

    The tanks were so humid to work inside of and still dealing with the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4