doh i can see i didn't give enough info, sorry
i'm thinking about transferring a rd28 to a petrol engine (at this stage, possibly the ford 4.0l turbocharged inline 6)
i'm wondering if the...
Type: Posts; User: brynk
doh i can see i didn't give enough info, sorry
i'm thinking about transferring a rd28 to a petrol engine (at this stage, possibly the ford 4.0l turbocharged inline 6)
i'm wondering if the...
g'day folks
i'm planning a petrol conversion on my diesel one of these days, and i was wondering if anyone can confirm that the transfer pump in the diesels is the same as the transfer pump in the...
+1 on carrying a charger - don't forget the extension lead!
(hope your trip went well and the alternator didn't shyte itself, since this thread is a couple of months older now ... !)
once you...
hahaha my wife & i are havin a laugh over all you ol ducks arguin over who's name is on the last slice of tea-cake! :)
i think benno has the call if he has the rims that i like the look of (no...
g'day benno - are you proposing a trade? if yes,could you please post some phots ?
pick up is in canberra, just down the road a bit from the ranga-in-chief!
ladies & gents g'day
4x maxxis bighorn lt 285/75/r16 8pr 122/119m
i have four maxxis bighorn muddies (tyres only) that are too bloody noisy for road driving; i replaced them with bridgies 693...
ok thoroughly karchered the shyte out of the likely lad:
- the front windshield seal
- under the body, particularly up in the wheel arch
- from underneath, the jacking point & sill
- the...
cheers kristoffa - windscreen seal is supple & complete with no signs of cracking or perishing... but i plan to test this thoroughly with a pressure washer in the next day or so.
g'day ladies & gents
our mate gusty is leaking water in the passenger footwell - it's not a drip like is shown in this thread -...
i received a timely answer from the bloke i bought the kit off regarding my questionable thrust bearing, which gave me the confidence to proceed with re-assy.
i can say from my experience that...
tony thanks again - i had wondered if diesels behaved the same ;
is there a method i can follow to check the timing of the fuel pump ?
closer look
7259
everything you need
7260
all the parts of the turbo, in pieces
7261
all the new bits in the kit with the old bits lined up next to them... there's a few extras which may...
thanks tony - there is definitely oil in the pcv line - when i disconnected it there was a couple of drips in the small hose
by the same token, there is a fair whack of black smoke on accel &...
more evidence of oiling in the compressor
7249
the shaft
7250
7251
the journal bearing - oddly, there was no retaining clip or equivalent... ? edit: yes there was (and had to be!)... i just...
pulled off the dump pipe
7230
i then marked the centre, turbine & compressor positions
7231
7232
my oiling problem is evident through the compressor... the question remains - is it coming...
g'day all
talked about a problem with gusty's turbo in this thread, where i can see oil collecting from the turbo through the intercooler to the intake -...
g'day bloke
thanks for your response - no temperature problem - 3/8 .. regular as laxative.
visco vent? what is this?
snorkel is forward-facing (force-fed by the air-stream)
driving fast...
g'day all
this thread was well timed as a problem recently surfaced with gusty's turbo. i followed the advice set out previously, but also took some phots as i went. apologies for the hijack feel...
thanks for answers so far yes definitely searching for steel to match existing (aiming for 6 wheels) cheers GUtsy have looked on ebay and found a few prospectives
r's brynk
thanks for the advice so far and Tony i would love to see that vid ! investigation continues into spec's, adr's & standards
g'day all
the need for a new front bar has become apparent. after a fair bit of research on what's available out there, it seems that short of scoring a bargain, you're looking at around $1000...
g'day all
i'm after some factory rims (1 or more) - i'm chasing the standard 16x8 JJ rims
r's brynk
well i installed a new clutch slave today ($150) and everything went fine. one thing to watch out for is that i did not receive a push-rod with the purchase; luckily i did not lose my old one.
...
fire in the intake system could also hint at a slight retardation in the timing - might be worth throwing the light onto it to see what happens.
another thing a mate of mine holds true is when...