Thanks mudski that’s what I wanted to know. Cheers.
Type: Posts; User: Patrol grub
Thanks mudski that’s what I wanted to know. Cheers.
No I have a choice of replacing with same but I’m wanting to go a silicon hi flow and that means the resonator box goes which is what I’m interested in. Weather it creates any issues not having it.
The pipe elbow to the turbo
Inlet on my 2008 CRD zd30 has cracked ang I’m looking at replacement options. Genuine elbow $395 no hope. While I can get after market elbows for less then half the price...
Hi all I have re entry done a egr blank on zg30crd the blanking plate has a hole to allow some gas through for the sensor. I am now having issues in ghat the car will start run for a couple seconds...
Awsome thanks all I was talking to him today and we decided to do what you are suggesting and we are going to try take it off and see how it looks appreciate all your help folks.
MudRunner it’s not the factory bar the bar is a custom made steel protection job that was made for my mates series1 it had to have 1/4 chop to make it fit snug and sit up higher on the back of the...
Hi all it’s probably here somewhere but after much searches ng they all started looking the same. Just curious weather anyone knows weather the rear bar off a series1 will fit onto a series4. I have...
Just looking at getting a rear protection bar off a work colleague. It requires 1/4 chop. My question is will a series1 fit into series4 and look half decent without major mods to the bar. I’m...
I usually do the same by filling up aroun 1/4 tank but did a trip a few weeks ago and got down a little to low gor me also last rank of fuel was Costco have you herd any bad reports about their fuel...
Ok cheers I have a scan gauge coming shouldn't be far away I spoke to Berrima diesel and they said to check fuel filter as at the revs I'm talking and the symptoms to them sounds like fuel starvation...
Well after a week of running around the issue has popped its little head up again. Had my mate from carline put his scan tool on and no errors and everything seems to be ok ie rail pressure at...
I have auto and it goes to 4000 easy have seen it get over that before but backed off real quick. Drive it like you stole it I say. Besides if it goes bang then the misses won't hesitate in a power...
Ok never had the issue before I did another reset of the computer and now reving to 4000 clean as has done before but this is good to know cheers for your input appreciated mate.
Yeh I disconnected the battery again and left it off for until this morning just to make sure the computer reset and it seems to have worked. I had it off for well over an hour the day I did the work...
Thanks Nisshead just had this replaced in a recall had it done and passengers side air bag recall done thanks for you help mate. Waiting for scan gauge then will work from there.
Yeh got one on the way cheers for your help.
Hi all have been complaining to local dealer at last two services (last being major) about low power and bad soot at all revs. Was told nothing wrong. ZD30 CRD motor. Have done some research and...
Just order standard rate springs if it's standard rate your after but like the standard spings on your vehicle they are limited to how they perform. Depending on what your going to be useing it for...
Would you recommend running egt gauge with this system. Also which unit would you recommend Scangauge2 or the ScangaugeE cheers Nisshead
Cheers mate I'll def invest in a set
Thanks three dogs I have duel batteries and after another look there actually 300kg not 250 as I thought I'll just have to add the mods I need most and watch the wait. If I'm starting to get to...
Thanks everyone I'm guessing I'll upgrade wiring and globes thanks for your help.
Thanks strop I'm guessing I'll upgrade wiring and gloves thanks for you help.
Cool thanks all for your input they are 250 kg progressive I'll be sticking with the genuine alloy bar but will have winch fitted and rear bar work done. Will also be installing draw. Duel spare tyre...
Hi all this is the pipe running from the turbo to the inter cooler is this where I put the nipple ( indicated by my finger ) to atach my hose for the boost gauge if not where and could you add photos...