G'day MAKKA
glad to meet you im at canton beach
Type: Posts; User: jgoose
G'day MAKKA
glad to meet you im at canton beach
Ok fair enough i did look into it a bit & going by what ive used in the past on other diesels etc thought it would be suitable the motor thats in the car at the moment is only a test mule i have...
67581
Heres a close up of the linksge ive welded onto the original tb45e linkage in reverse so the cable (hyundi cruise control cable) opens the I P when the accelerator peddle is pressed so ive...
John
Ive had your comment going over in my mind im starting to think i might of missed something or havnt planned my mod out right
How do you think that ive limited my options for when i mount the...
Ive been doing mods on cars since i was a teen ive put 351's into celica's & gotten them rego'd etc so i dont mind making brakets as i go its helping keep my mind off things
Since ive had it back...
Its the td42 intake i made a 90 with a mounting plate to suit yhe intake & the TPS & bolted it straight up i did have my hi mount fitted but due to my health just ran out of time & paitence to finish...
6752667529675306752767528
Hopefully the pics work ill chase up more off my pc as for yhe alt conversion its just about the same deal as already listed as for my A C the GQ A/C braket was modded to...
Thanks for the words of encuragment re the BIG C hopefully its all done & dusted now both cancers were found by accident while chasing problems from a work place accident but onward upward
I have...
Hi all ive just finished my conversion from a TB45e to a TD42 t. Now i havnt done the turbo yet but have been driving my gu around for about 5k with not a problem i started by purchading a td42 about...
Hi gerry have you still got the 4.2?? im only at toukley
Hi all thanks for the kind words i relise its not a job for everyone i just like to show ppl how things can be done without paying top dollar at least a lot of the job isnt too hard to tackle at home...
Now that you have made sure everything is clean slide the axle back in BUT DO NOT REST THE AXLE ON THE SEAL THAT YOU JUST INSTALLED INTO THE HOUSING as you slide the axle into position rotate it as...
Make sure that all of the axle assembly is clean including the splines. Remove the the old seal in the axle housing i use an old slide hammer that i made up but you can get away with a screw driver...
Remove the rag & make sure everthing is clean fitting a new lock wasker is best but if you dont have a new one clean up the old one & put it into position clean up the nut & screw it down then lay...
If you have acess to a press it makes it easier at this point to fit the bearings in the past i have put the bare axle in a cool room to help shrink it i have also used my hi lift jack with a long...
Turn the bearing housing over & drop in one of the greased tapered bearing take the housing seal & gently tap it into position if you dont have a socket or tube the same diameter as the steel of the...
When every thing is cleaned sit the bearing housing on a block of wood with the side that the seal goes into face down. What i do now is heat the housing for 10-15 mins & take the outer race from the...
Remove the tin plate that is held on via the axle studs & clean & inspect all the seal faces if you can catch your finger nail in a groove worn by a seal you will need a SPEEDY SLEEVE to repair it...
When it has come apart remove the old bearings & support the housing on timber so the outer bearing shell can be knocked out. Using one of the old bearings place it in the top of the housing & heat...
Now this is the hard part. If you have acess to a press use it it mite cost you a six pack at the local mechanic to use his as i said im out on my property & dont even have a dunny let alone a press....
Here are the other pics it would not allow me to post all of them at once
Im doing this repair on my property so i dont have a shed or work bench at this stage so im just using my car trailer as a work bench. Stand the axle on your bench & to remove the A B S stator i use...
As i said before i assume everyone knows how to remove the brake caliper & support the caliper so i does not hang from the brake line & remove the disc
Then remove the bolt that holds in the A B S...
Hi all sorry for the delay ive had to return to the coast & havnt had time to start with the run down on how ive done the job. Im assuming that every one knows how to remove the calipers & that they...
Hi all. Ive knocked it over all went well i even changed the diff oil no more noise on the RH SIDE when turning left. I will try to load the pics & details tonight. @ the moment i have an...