Wanted 7 bolt spacer for a zd30 or qd32
Thanks David Ph 0409632055
Type: Posts; User: Dagwill
Wanted 7 bolt spacer for a zd30 or qd32
Thanks David Ph 0409632055
Doing an engine swap. Bought a new bare long qd32 via alibarba. Im swapping all the extras from a TD27 onto it, manifolds starter etc.
Now on the rear right hand side of the sump, pointing upwards...
So modern fuels dont have the lubrisity of old fuels.
Ive heard of many people adding 2 stroke oil to the tank. ,,, At $20 a ltr , id rather have an extra 10 ltrs of diesel.
Now years ago I had an...
Starts out fine, but once up to temp its just a matter of time and it goes into limp mode, engine light comes on and the tacho is dead. If it sits turned off till it cools, all is good again , full...
RELIEF,,,,,,The mark on harmonic balancer was an extra mark [looked exactly like TDC mark ] and the yellow marks on scossor gear were actually DD marks.
So as it had turned much more than I thought...
Thanks for the help, I was hesitant to start turning the engine too fr forwards as the zd30 is a "hunting engine" and TDC and CC marks only line up about 1 in 20 revolution,, along with cam timmings...
Zd30 2006
Hi everyone, had to replace injector pump, so aligned all timing marks, undid the allen key plug and used one of the fan bolts to lock the scissor gear.
Now while removing...
Hi ive seen many used Japanese engines on Alibarba, are there any pitfalls buying said, I know theres no real warranty, appart from that has anyone bought one. Are they any good. re there lots of...
Hi I have ordered a new long QD32 which I was planning replacing a TD27 in a Terrano but my sons IP has just gone on his ZD30 Navara , maybe it should go in there.
If all the mechanicals of engine...
hI, That stuff is very good on petrol motors, diesels have twice the compression. The stuff explodes when the piston is only half way up,,, not good,,, way too early,,, knock the shit out of your...
Hi, GU patrol, ZD30 Problem started whith car going into "limp" mode, foot of the gas, back on ,back to normal. Happened once or twice, seemed like nothing to worry about. Till yesterday while...
Short story, Stupidly sent 12v back along crank sensor signal line, qhich I now have learned runs on a 5v system. Heard louder than normal click of a realay or solenoid, sounded as though it came...
Thanks, i will take on board what you all said,,,, theres been more than one time in my 67 yrs that ive said to myself. "That would have been fine if id left it alone"
That said what I intend to do...
Hi, I have the injectors out at the moment and was wondering if i should clean the nozzels.
Looked closly at the end and I cant see any little holes at all.
Is it reletivly easy to put them in a...
ANOTHER EXAMPLE OF MY FALABILITY
Although it seemed only high spots were clean, the fact was, that the dark places had not been cleaned enough.
I had been too gentle, not wanting to damage the...
Ready to fit the new head.
scraped off block face and noticed shiny rings around cylinders and other places , possibly just a witness mark from the gasket.
Gave it a good rub with a large flat...
Later in the day
removed the gear from camshaft,,, Hmm no hole in the back ,its a blind hole that holds the dowel. The broken off piece is still in there. Tappy Tappy ,bang bang , wont come out....
Hi ,it seems that the bolt holding timing chain gear onto the cam gear became loose and the dowel that drives the cam gear broke [ hence my other post on head removal ]
There was a little damage...
Thanks Mickhead, Yes i was going to replace that short little hose ,, but the Eng. # I would have definitely missed.
HOORAY. ,,,, Stupid me had not taken out the bolt that went through the top of the water pump, through the inner timing case and into the head. Thank goodness I had not used TOO much force at this...
Thanks Mudski, Looking at your pic made me rethink, not sure but maybe its frozen onto the front block to head locating dowel. It does seem to rock from a center closer to the passenger side, which...
If there is a dowel its going between the inner timing cover and the head ??
Hi, Ive come to a halt, and need help please.
Removing the head without removing inner timing cover.
Head is stripped, all bolts are out,, yes and the two behind timing chain tensioner.
I have...
Hi, Engine in my auto has done 360K and have just sheared the little dowel from timing sprocket driving the cams, so same result as broken timing chain. I can get a manual engine and just do a swap...
Is there an "edit post" function anywhere,,, is it possible to edit posts.
just found that fuse is only live while cranking