OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

Search:

Type: Posts; User: Bambill

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    118
    Views
    50,765

    .......................

    .......................
  2. Replies
    118
    Views
    50,765

    ...................... Marty

    ......................


    Marty
  3. Replies
    11
    Views
    8,006

    Matt I can tell you that, the turbine housing on...

    Matt I can tell you that, the turbine housing on your turbo is made for the supplier of your turbo and cannot be brought elsewhere.
    And there are other internal differences between say your turbo...
  4. Replies
    23
    Views
    5,703

    LOL, yeh sorry was a bit. If it helps, I put a...

    LOL, yeh sorry was a bit.
    If it helps, I put a 3.5" exhaust on another ute the other day with a UFI 18g and DC pump with the same kind of results. He also reports a slight drop in EGT's aswell which...
  5. Replies
    23
    Views
    5,703

    TD42T, larger turbo and 36ish psi boost. 3.5"...

    TD42T, larger turbo and 36ish psi boost.
    3.5" exhaust from back of turbo with a straight through type muffler.
    Reasonably quite, in fact quiter than most. Picked around 100-150rpm in spool time...
  6. Replies
    67
    Views
    21,976

    Hmmm, if you are half handy with a spanner, just...

    Hmmm, if you are half handy with a spanner, just buy a GT2863 without the exhaust housing.
    Swap the core over using your exhaust housing. It will be a straight swap.
    The tune will not be that far...
  7. Replies
    14
    Views
    22,976

    Paul, Your an inquisitive bugger, lol. I have...

    Paul,
    Your an inquisitive bugger, lol.

    I have a 12mm pump built by UFI in Perth. It uses a 1hdt head, plunger and cam plate.
    Most 12mm pumps would use the same combination of parts.
    You could...
  8. Replies
    8
    Views
    4,049

    You sure the lifters are hydraulic? I think they...

    You sure the lifters are hydraulic?
    I think they are solid or you wouldn't have to reset them all the time clearance.

    Marty
  9. Thread: TD42 Boost ?

    by Bambill
    Replies
    50
    Views
    19,969

    I will ad though, (memory is slipping), that in...

    I will ad though, (memory is slipping), that in the months before I changed turbo and pump I was getting mid 11's from the standard pump and turbo. Was 17 ish psi lots of timing, 4" snorkel, smallish...
  10. Thread: TD42 Boost ?

    by Bambill
    Replies
    50
    Views
    19,969

    Yeh from the day I drove it out of the show room...

    Yeh from the day I drove it out of the show room the best I could get was maybe 18's.
    But with ample power you simply don't need to flog it to get it going. Normal everyday driving, with it spinning...
  11. Thread: TD42 Boost ?

    by Bambill
    Replies
    50
    Views
    19,969

    My GU work ute, which does 6-700km every week has...

    My GU work ute, which does 6-700km every week has as mentioned, earlier around the 280 odd hp mark and around 690-700nm.
    It has 400k km on it and has never been toouched. Never opened up other than...
  12. Replies
    19
    Views
    23,689

    Go and search Patrol4x4.com A couple of the guys...

    Go and search Patrol4x4.com
    A couple of the guys there have turboed the inline pumps with success.

    Marty
  13. Replies
    15
    Views
    4,606

    I did run a 11.5kg twin plate for a while which...

    I did run a 11.5kg twin plate for a while which is 16.5kg lighter than the standard flywheel and clutch and it was great,
    Except for the noise being solid clutch plate.
    Drivability not a issue.
    ...
  14. Replies
    15
    Views
    4,606

    I know of 3 cranks breaking. At this stage I'm...

    I know of 3 cranks breaking.
    At this stage I'm not to concerned about it really, I have a feeling driving style may have contributed to 2 of them and the other was a earlier non factory turbo...
  15. Replies
    15
    Views
    4,606

    TD42. Off topic from your question, sorry...

    TD42.

    Off topic from your question, sorry about that.

    Marty
  16. Replies
    15
    Views
    4,606

    Hmmmm still Garrett based on a 2871. Billet 71mm...

    Hmmmm still Garrett based on a 2871.
    Billet 71mm compressor wheel with extended tip, normal 6x6 blade configuration not full blade style.
    Modified 53.9mm (standard GT28) turbine wheel.
    Hopefully...
  17. Replies
    15
    Views
    4,606

    To be honest I have never had a exhaust on long...

    To be honest I have never had a exhaust on long enough to notice anything.
    Changing turbo on the weekend, I will have to unwrap the dump, I'll have a look.
    No issues with moisture, it all dries...
  18. Replies
    15
    Views
    4,606

    Anything you can do to maintain heat in the...

    Anything you can do to maintain heat in the system upto the turbine is good.
    More heat, better corrected gas flow for more drive on the turbine, so yes it should spool a little quicker and be more...
  19. QUOTE=Jacket_1985;343640]you seem to have a bee...

    QUOTE=Jacket_1985;343640]you seem to have a bee in your bonnet about this Marty.

    i start a few threads asking about fuel pump upgrades, and you comment on every one and keep telling me i have a...
  20. But you don't belive in warranties!

    But you don't belive in warranties!
  21. Replies
    17
    Views
    12,259

    I will suggest it is just gear rollover. When in...

    I will suggest it is just gear rollover.
    When in neutral and it is making the noise, without using the clutch, put a bit of pressure on the gearstick like trying to put it into a gear.
    If the noise...
  22. Replies
    9
    Views
    2,909

    If it is knocking, you may find it has broken a...

    If it is knocking, you may find it has broken a injector spring also. I have had this happen a couple of times. Broke the spring, jammed the nozzle, knock knock knock, white smoke, miss at idle.
    It...
  23. Replies
    14
    Views
    3,499

    Oops I forgot about this on the other site. If...

    Oops I forgot about this on the other site.
    If it is a .48 exhaust housing in T3 that is about right. It maybe a little slow in response as the exhaust side is slightly larger than the GT28...
  24. Replies
    21
    Views
    16,968

    Yes Matt has posted up some good reading and is...

    Yes Matt has posted up some good reading and is very interesting.
    Temperature drop across the turbine is part of its operation though and the cooling and expansion of the gases is what drives it....
  25. Replies
    21
    Views
    16,968

    You really need to stay away from the so called...

    You really need to stay away from the so called high flowed turbos.
    Either machining housings for a different CHRA or whatever.
    The standard compressor housing is not large enough to cope with...
Results 1 to 25 of 52
Page 1 of 3 1 2 3