OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

Search:

Type: Posts; User: shantillylais

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Hi Trev, yes there was a relay in there, but...

    Hi Trev, yes there was a relay in there, but wasn't wired to the Cooling fan fusible link, or to the front of the car. I came to the conclusion that the plug I had near the bonnet latch is for...
  2. oops sorry about that I didn't realise I had hit...

    oops sorry about that I didn't realise I had hit the button twice. How do I remove one?
  3. finished my fan install, using a 4 pin plug fan....

    finished my fan install, using a 4 pin plug fan. By providing 2 power feeds both through relays, I have achieved a 2 speed fan. The first is the existing relay that I had to make a 2 wire loom for...
  4. pm sent Trev

    pm sent Trev
  5. thanks mudski that is my plan B :) but for the...

    thanks mudski that is my plan B :) but for the moment I would like to try and use the factory wiring if I can.
  6. thanks Trev, much appreciated. My aircon is...

    thanks Trev, much appreciated. My aircon is average at best. The diagrams I have used are from the manuals on this forum and they are 2004 so yours are possibly more current. As far as the plug is...
  7. installing a a/c condenser fan on my GU8

    Like most with 2012 crd's, mine doesn't come with a fan, so ordered a fan from wreckers, and checked out the plug taped to the loom by the bonnet latch.
    My plug has 2 wires, green/yellow and...
  8. mudski sending you a pm, hope its ok. after a...

    mudski sending you a pm, hope its ok.
    after a hic-up with my pyro, took it for a cruise down the highway at 100km on cruise. Boost was varying all over, but mostly around 15psi, pyro was about 300....
  9. the kit arrived today mudski super quick thanks,...

    the kit arrived today mudski super quick thanks, have the pyro in now, taking it for a spin this afternoon to see what its doing before I start on the install of the kit. thanks again.
  10. that's a nice offer thank you mudski but yes I...

    that's a nice offer thank you mudski but yes I have one. I am also making enquiries about a intercooler upgrade even tho' there doesn't seem to be any leaks at this point.
  11. ps, hoping that bigguwesty Kallen will chime in...

    ps, hoping that bigguwesty Kallen will chime in since he is nearby for a guide as to which places to help with exhaust/pyro bung etc
  12. thanks guys, I just bought the kit on ebay from...

    thanks guys, I just bought the kit on ebay from Northern4x4, now I see that is mudski
    I cant do the pyro yet until I can get an exhaust place to do it for me, normally I would do it but hurt my hip...
  13. Hi guys, new to all the nads stuff, and lots of...

    Hi guys, new to all the nads stuff, and lots of acronyms etc to learn as well as figures you all talk about. However, I have also had it suggested to me to get a remap done (pulling power plus egr...
  14. Replies
    23
    Views
    4,020

    Hodge I did actually read that thread some time...

    Hodge I did actually read that thread some time ago, and took on board what some said about too much grease etc. I only smeared grease on the surfaces of the gears pins and other touching parts, and...
  15. Replies
    23
    Views
    4,020

    that is the condition of my clutch pin and its 18...

    that is the condition of my clutch pin and its 18 months old
  16. Replies
    23
    Views
    4,020

    Hello Hodge, yes that is the one, when I bought...

    Hello Hodge, yes that is the one, when I bought the winch 18 months ago, it had the wrong booklet in the box so I contacted them, and they emailed me a correct one. The diagram is in that. I am...
  17. Replies
    23
    Views
    4,020

    I have just finished servicing my Runva 11xp...

    I have just finished servicing my Runva 11xp Premium winch, that is only 18 months old. When I first purchased the winch, I opened up the gearbox and cleaned out the factory grease which I was...
  18. Replies
    75
    Views
    19,749

    raising an old thread again, mainly because I had...

    raising an old thread again, mainly because I had read and re read lots on putting a Runva 11xp winch in the Nissan bar. I bought a Nissan Bar dated 2012 on Friday, and today finished servicing my...
  19. thanks for that, a side job when servicing the...

    thanks for that, a side job when servicing the wheel bearings next :)
  20. hey there the evil twin just because I am a...

    hey there the evil twin just because I am a little lazy atm, is there a thread on doing this auto hub mod? cheers Lana
  21. Replies
    23
    Views
    4,741

    I found the reason my fridge slide is tight, and...

    I found the reason my fridge slide is tight, and I bet others are the same. On the right side of the fridge slide, next to the fixed top, there is a "look good" trim, that runs the full length. I...
  22. Looks like I just found the problem with mine :)...

    Looks like I just found the problem with mine :) cheers for that .... Lana
  23. Replies
    9,135
    Views
    788,478

    thanks mudski, I had seen similar, but I wanted...

    thanks mudski, I had seen similar, but I wanted more a usable shelf on top. It will be from the backseat to the door (950 long, and from the fixed side to the 3rd row grab handle), so mine will be...
  24. Replies
    9,135
    Views
    788,478

    finished the install of my 4WD Systems drawers,...

    finished the install of my 4WD Systems drawers, very happy. Did the door opening mod so the fridge doesn't hit it, next is to make a removable mesh "cage and shelf" to go around and over the fridge....
  25. Replies
    23
    Views
    4,741

    Hodge that is a good point about the hole and...

    Hodge that is a good point about the hole and things falling into it. I agree about how tight they are too, but I thought that was because it is new. Might need a barrier mod to stop those things...
Results 1 to 25 of 64
Page 1 of 3 1 2 3