OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

Search:

Search: Search took 1.00 seconds.

  1. Thread: G'day from Bris

    by Dhuck
    Replies
    5
    Views
    693

    Welcome to the forum mate

    Welcome to the forum mate
  2. Thread: G'day from Bris

    by mudnut
    Replies
    5
    Views
    693

    Welcome to the forum.

    Welcome to the forum.
  3. Replies
    5
    Views
    693

    G'day mate, welcome aboard

    G'day mate, welcome aboard
  4. Thread: G'day from Bris

    by AB
    Replies
    5
    Views
    693

    Welcome to the forum mate!

    Welcome to the forum mate!
  5. Replies
    5
    Views
    693

    Welcome mate!

    Welcome mate!
  6. Replies
    3
    Views
    2,147

    ZD30 Aircon Compressors

    Hey Lads,

    Long time lurker and reader, but i think this may be one of my first times posting.

    This thread is discussing the specifics of replacing the A/C compressors in the ZD's and some of...
  7. Thread: switches

    by MB
    Replies
    17
    Views
    4,277

    G’day DT mate! Be careful listening to...

    G’day DT mate! Be careful listening to MudRunnerTD, he’ll turn your truck full comp worthy for sure:-)
    Still take a little loved one/s out and about sometimes in the ute and dogs also love to jump...
  8. Replies
    11
    Views
    7,237

    I had no issues when fitting a 3" system to my...

    I had no issues when fitting a 3" system to my 2009 Crd. Just had the car on stands, so the front wheels were just off the ground. I'm sure I didn't have to get anything out of the way. The big bitch...
  9. Replies
    11
    Views
    7,237

    No need to lift the car up mate, however if yours...

    No need to lift the car up mate, however if yours is ZD30 powered then the OEM dump pipe/DOC (Diesel Oxidation Catalyst) will not come off unless you drop LH side of the sway bar (front).

    Regards
  10. Replies
    60
    Views
    80,131

    Sticky: DIY Wheel Bearing Adjustment.

    So in heading away for Christmas and as part of my pre-trip check I tightened my front wheel bearings. While I was at it I thought I'd take some pics and show how easy it is.

    So I have jacked the...
  11. Thread: AC Bearing

    by johno90
    Replies
    35
    Views
    7,953

    You can get them for that price haha, if we are...

    You can get them for that price haha, if we are talking about the bearing behind the clutch then its an easy job all you need is a puller and a press make its easier. or a good hammer. Use the puller...
  12. Thread: AC Bearing

    by jay see
    Replies
    35
    Views
    7,953

    The a/c bearing can be replaced. I did mine...

    The a/c bearing can be replaced.
    I did mine about a year ago. Plenty of info on the web on how to change, not too hard of a job.

    Best is to take off the belt and spin the a/c by hand, if noisy...
  13. Replies
    9
    Views
    4,197

    You can buy on ebay a complete set up and wired...

    You can buy on ebay a complete set up and wired to turn off DRL`s when the, either parkers or headlamps are switched on.
    I have done this and it works a treat.
    I can`t help you with a link but...
  14. Replies
    9
    Views
    4,197

    It is a weird rule like a lot of others but, Yes,...

    It is a weird rule like a lot of others but, Yes, aftermarket DRL's must turn off when headlights are on whilst Factory fitted don't (altho most do).

    I wouldn't bother with a relay for load as the...
  15. Replies
    9
    Views
    4,197

    You could wire them to your parkers and have a...

    You could wire them to your parkers and have a toggle switch on the earth wire,
    to turn them off when your headlights are on, The toggle could have a LED in the
    end of the lever
  16. Replies
    8
    Views
    24,567

    Sticky: How to guide - relays

    This is a good site to understand all about relays.

    http://www.mobileinformationlabs.com/How%20To%20Guides/Relays/HowTo-Relays_understanding_Intro.htm
  17. Replies
    186
    Views
    308,662

    Sticky: DIY CV and Swivel Hub Rebuild Thread

    OK So one of the big maintenance items that we may attempt at home is a CV swap or Swivel Hub Rebuild. I have done this a Few times and have had these pics ready to go for ever!! I have referenced...
  18. You going to need a calm head and start with the...

    You going to need a calm head and start with the basics.

    Start at the battery, check and clean the terminals. Hows the main earth lead to the body? the one just under the battery. Didn't you just...
  19. Sticky: Thanks to Todd and AB for this, I'm sure members...

    Thanks to Todd and AB for this, I'm sure members will find it extremely helpful
  20. Sticky: Nissan Patrol GU Y61 service manual INC Supplement I, II, III, IV, V, VI, VII & VIII

    Engines covered;
    TB42S
    TB45E
    TB48DE
    RD28ETi
    ZD300DDTi
    TD42Ti

    Thanks to Todd, we now have the full Nissan Patrol Gu Y61 service manual including the following supplements.
  21. Here is some info I Have on the subject. And...

    Here is some info I Have on the subject.


    And ADR45, they are not called "Work Lights" they are called "Search Lamps". ADR13 actually restricts the fitment of a white light to the rear of the...
  22. The three way switch is a good idea. Flexibility....

    The three way switch is a good idea. Flexibility.
    I don't think it would be legal to just wire it through the reverse switch only.
    I call it the "f**k off light" for when someone gets to close at...
  23. Replies
    516
    Views
    496,997

    Sticky: Blocking the EGR Valve

    What is EGR (Exhaust Gas Recirculation) and why should I block it?

    Wiki link for in-depth explanation.

    TLDR;
    *EGR works by recirculating a portion of an engine's exhaust gas back to the...
Results 1 to 23 of 23