Search:

More humans on the road nowadays are far more intellectually challenged than any roo.

I disagree, Emu's are the dumbest animals on the planet. Bloody kamikaze feather dusters

Certainly important - I used an old head bolt , grinded flat a bit on one side.
\

A while ago I posted a question about replacing a head gasket. many thanks to all who helped with advice.
The head is off , and the valves looked they could do with a clean , one was not even...

Now that makes perfect sense to nuffy me AB Mate, ping pong, would explain the valves open exploding with inwards & outwards ignition after TDC/BDC if that’s correct?


Sent from my iPhone using...

FWIW: It was honestly a genuine question as ‘Cyclists’ well known experienced....arrogantly traverse our daily work routes enroute to Selfish Coffee’s [emoji856]
Thinking I should increase my own...

Mind Blown!!

81257

AB, yep, more work and I am just about over the fiddling around to be honest. I will have a look tomorrow as the config you suggest is probably the best. Thanks.

That's interesting AB. I did have a pair of 2" projector lights and took them off as they got so damn hot I was worried about them melting the housing they were in. I will have another look at...

Did you even look at the specs Arfa. Try some offset bushes in the radius arms and setback bushes in the rear if the arms. Get rid of any RTC damper as this hides alot of issues in the steering...

FWIW for the last 40+ years I’ve always taken my cars to a specialist wheel alignment/suspension shop. That’s all he does and has ever done. Never had an issue, I always rotate all five tyres and...

I think you should expect your money back . If it were me I would be making that firmly but politely clear to whoever is in charge & telling them that both a) it was fine before they adjusted it & b)...

Agreed AB Mate!
Good Hard Yakka memories as a kid too as late as the early 80’s having to travel with Dad further out of our ‘Green Wedge’ just started then I believe to the likes of outlying...

I remember having cuts all up my arms, legs and on my face from gathering enough blackberries for my mum to make a pie.
It was always worth every cut.

oh some wonderful memories on here..........

I remember the Black and White TV - Test Patten after 11.00pm
my Father going to Vietnam in '67
driving across the Nullarbor Xmas '68 - was just a...

I have had ot happen a couple of times.

I had a flexi joint fitted just after the flange of the y piay it has not played up since

Bigcol I ran that new generator mixer on my 650 4 barrel powered chev troopy
Trouble was it only feed gas to the back two barrels , we farted around with and
ended up getting fuel to all 4...

just found this - sorry Arfa




sounds like the old "ring" for the gas - sat on top of the carby, under the air filter -
similar to this
68764

the Sprint Gas type looks like this

yep common for the engine pipe to crack at the flange, most treat it as an excuse to fit extractors

Umm nope. Fan case is the case to the left with the motor sticking out the bottom. Evap case is in the middle and is very easy to get out once you know how. Even on a gu there is no need to remove...

Sounds great mate. Can't wait to see that thread and pictures.

Here's a few,

Kimberley Blue Tongue - took up residence under the groundsheet of our tent. Camped out in the dunes on west coast of Dampier Peninsula, WA
...

g'day mate and welcome aboard

On the water side of the gas system fit "Ys" instead of TEEs for a more efficient water flow
and less chance of cavitation. Also don't forget to bleed all air from the system as well.
...

I was able to source the pump from Burson for around $130 on mine. Also available for same price on ebay.

Your should look the same except the EFI pump is a much higher psi one.

The Fuelmiser...