Most exhaust joints can supply and fit a flexi joint. It cost me $70 to have a joint suooledand fitted
Most exhaust joints can supply and fit a flexi joint. It cost me $70 to have a joint suooledand fitted
I have had ot happen a couple of times.
I had a flexi joint fitted just after the flange of the y piay it has not played up since
Do a search on this forum as i posted picture about 6 months ago.
The idle issue most likely wont be caused by the vacume hoses.
1 loose bottom part of the carby -remove air cleaner and see if...
I remember attending a 4wd club meeting were the local Nissan dealer attended to do a sales pitch on the new, great patrol fitted with a zd30
the dealer stated that it was the best, most reliable...
Welcome
Getting away is one of the main reasons a lot of us are patrollers
Depending on the model a rear lsd centre can be put in the front
I have a rear H233b lsd from a mk wagon in the front of my gq as the both have the correct spline count on the axle. To retain the...
I ended up replaceing the rocker bolts with normal bolts as the head of my bolts werestripped.
it was around m6 * 25 mm
I dont think the extension is 4 mm, its around 2mm. I have heard of people extending their existing button. The main improvement is bettle idle, an the motor is a bit more responsive.
I don't...
A combination of extended rotor button, pertonix ignition and points do help.
Have you changed the condenser and coil, as these have been know to cause missfire.
you have done the rest
The...
The 80 channel is a lot softer, when received on a 40. And the 40 channel is a lot louder when received on a 80.
The first 40 channels on the 80 channel cb are the same as a 40 channel. The second...
Sounds like a partially blocked petrol filter.
Is there a Silver canister near your battery with 2 hoses - try by passing it and see if it makes a difference.
There is also a gauze filter...
Hi Dom,
I suspect the IMPCO 300a has a power valve built in see item 3
http://www.teecoproducts.com/Catalog/PDF%20Files_Catalog/IMPCO/IMPCO%202006%20CAT-300A%20Series.pdf
If you are using a...
They work ok - keypad programmable etc.
They are not type approved for use in australia - so the ACMA and boys in blue can charge you for having one.
It wont be the differance betwen the 40 / 80 channel rigs as long as they are on the same channel. (and between channels 1 - 40)
40 - channel reciveing a transmission from an 80 channel - the...
tb42 and rb30 carbys are basically the same.
The rb30 is known for running out of fuel on step hills, I have not experianced this on the tb42
I have a couple of swags - a dune and a custom built one (was given to me).
I use dune, and my 12 yo uses the custom built one. I replaced the mattress in the dune with a thicker and wilder unit...
The replacment springs and shocks is a good idea.
I have had a few vehicles running poly airs, they help with the ride but should not be the primary shock relief.
Have you pulled the faulty air...
http://www.ebay.com.au/itm/Commodore-Clutch-kit-VL-r31-Skyline-Patrol-3-0-Ltr-RB30-Eng-NSK24003-/230897748542?pt=LH_DefaultDomain_15&hash=item35c2940a3e#ht_2094wt_1362
A clutch kit normally...
The last couple of clutch kits i have brought fropm sunbury brake and clutch - good price (they are on ebay). Also the vl commodore clutch for the rb30 is he same kit as the patrols - but a bit...
I would pull the rocker cover off and crank the motor. Watch the valves - you should see if any of them are stuck as it wont move.
But - it could also be a tappet out of adjustment, lobe gone on...
Bosch GT40R Coil = need ballast resister, Bosch GT40 Coil + no ballast resistor
on crak there should be 12 volts going to the coil, while running around 9 volt using a ballast. But I would upgrade...
Sorry grave dig.
The tb42s and TB42efi fans are different and cannot be swapped (the centre are differant size). i currently have a new tb42e fan - need one for a tb42s
Zoki, can you update you signature with model and engine type - it helps when people respond to your posts
With this fault "uses all the fuel in the bowl and it stalls" could be related to a partial block fuel filter. There is one at the carby where the fuel enters the carby, and I think one in line and...
Did you have a look at the link, I posted as it has the ecu details.