RIP Whitie. Not a dog but our pet goat that acted as if she were a dog. We bought her and her daughter in 2004-5. They were both pregnant, so we think Whitie was around three to four years old when...
RIP Whitie. Not a dog but our pet goat that acted as if she were a dog. We bought her and her daughter in 2004-5. They were both pregnant, so we think Whitie was around three to four years old when...
It's very satisfying when aftermarket things fit perfectly :D
http://www.nissanpatrol.com.au/forums/images/imported/2023/10/51.jpg
Gave the old GUrl a quick scrub before getting her dirty over a 4 day Fecking weekend starting this Friday at Enoch’s point on...
Bloody hell! very nice!
Also loved the fact that the tire swing pivots with the door and not by itself. That side of the swing you need not worry with undone latches! Really inspiring!
Well done mate. Top notch work done. I widh my welding was neat like that.
Gonski :) ...
Not a doctor? You could bloody eat off those boots! Do you have an actual work pair and then a pair for when you just wanna take photos? Nice work. Assuming the rear bar will.be produced in house...
That's wicked mate! Love your work
Sent from my SM-G988B using Tapatalk
We discussed finishing the floors, and being we had always planned on moving the kitchen we felt it didn't make sense to redo the floor twice. Made a start on it today.
Started here.
86878
...
Moving away from the Introduction section of the forum here is my thread about my new, to me, car. Pearl, her new name because her paint is Ivory Pearl, is a 2019 Y62 Series 4 Ti with 61k on the...
Haha that's excellent!
Sent from my SM-G988B using Tapatalk
Love the panel decals mate, amazing camouflage! :D
Mine has never gone off, but i have always known them to come out of the top of the dash, meaning the whole dash needs to be replaced if they operate.
This is also the reason why dash mats have a...
Not mine 86856
Well i hope you pull through ok and i'll keep an eye out for a 3L GU amongst all the other 3L GUs :driving2:
Ah bugger mate, feel for ya. I've not been using mine hardly at all but clinging on to it. Like you I'd be so upset if circumstances meant it had to go.
Just changed a 2010 set of headlights, some notes below
* definitely remove headlights to change globes
* remove grill first, use flat head screwdriver to pry up centre of 4x plastic screws then...
Settle down, settle down, this will take a while :coffeetime:
I'm back after years of other Nissan projects and have at last started to revive my old Trol.
it's been stood un-used for at least 3...
I can't see the video it's saying it's private.
How are you testing the starter? are you bridging the two large terminals together or are you supplying power to the smaller wire on the solenoid?
...
Just a quick one in regards to winch hooks.
You should always point the opening of the hook pointing upwards.
Why?
Because if the hook should fail by straightening out or a forging/casting fault...
He will hate me doing this but our good mate Lucas has been a bit silly and hurt himself pretty bad... playing on his dirt bike he came a cropper and binned it at 120kmh on dirt and has hurt his...
Almost never use the back seats,
So I pulled them out and made up some shelving to go there.
ok remove the wheel and mark your hubs with a centre punch so you can put them back with the orientation and also using your centre punch put a little L and R on the left and right free wheeling hub...
G`day mate
It`s nearly over bloody fastest 3 months l`ved live in a while.
What a place so much to see and do and not enough time
Covered around 8000ks so far and a few on the water in the flat...