Search:

2 hrs transferring 4l of hydraulic fluid into the hydraulic winch tank, holy shit that pumping is hard work under the car. reconfigured the interchiller pump circuit back to standard, still a few...

Yes it's what sold me, I look like I can stack a large and 2 stalls on top of each other as two large are too tight it looks. Anyway will see, they have some good options, as do the expeditions

Procrastinating about the format of the rear pod, bit the bullet today and bought the starter pack from TRED, which has a 55L and 2 x 27L units. Combo seemed to work a bit better than the Expedition...

Slider kit finally arrived after 6 weeks - they must have been busy. Looks a good kit, precision made, all notched, just need to weld then paint, happy days. Going to plate top and bottom using the...

You can get these clips on ebay or via Patrol a Part, not expensive at all.

I purchased a unit that takes a plastic 30l bin, on the basis the last one ended up a pigstye with food and mud etc - will see how that works out I guess.

Unscrew and unbolt all the window track assy then lift the glass out vertically thru the window slot - the gap will increase to around 25mm and its straight forward, even safe enough with window tint...

Priorities and responsibilities, nothing more. Walking away will degrade the delivery program and put the site at risk. I won't do it. Simpson Desert isn't going anywhere, can do it later. Holidays...

Was always on the cards, this place is out of control, and very reactive. Lots of delays in baseline data supply, financial release, contract awards processes of 8 months - stupid. I now have a log...

Barlows are OUT. Project work collision on site, 3 major activities to execute before August, cant get away. Not happy.

Have been using this for the last 3 yrs on site , especially after the wet when the flies and mozzie population explodes. Used in combination with a fly net and happy days.

They are great, bought one in 1988 and yet to use it in anger apart from rooting around in the backyard testing it. I see yours has a gas bottle - must look at mine to see if it has that flexibility...

I would recommend before application of the anti rust system that you thoroughly wash the area with a rust converter product - plenty on the market - Bunnings have a suitable one, as this will arrest...

Swapped out the Aeroflow Lift Pump to the carter Black today, was a journey of differences, but 4 hrs later all done with new mounting configuration. I have heard a lot of people saying the carter...

The beast is home with the canopy on, thanks to MB and his trusty shed and tractor. Boost pump developed a faultand essentially stopped the car, think I will be looking at a different make, the...

Oh shit, he has started again, god help us! OK what does that mean in plain english please????ps see ya tomorrow at 9

I used to do the dealer servicing run, simply made best use of my time and effort until I found they were using 1st year apprentices and not completing the scope of the schedule and charging me for...

@MB, have a look at these clamps as an alternative. The unit you used is heavy duty for sure, the link below has a distinct difference in that it has a spring effect that compensates for the...

A few of us, led by MudRunnerTD, have utilised old rear seat frames that mount to the existing points in the car, then put the plate you show welded to the frame. This gives you an air gap under the...

Getting closer, inch by inch. Ran the big wire down to the back today, sheathed it in 3/4" heater hose for mechanical protection, spent a good 2 hrs resolving a potential hot spot where Brunswick...

John, the Willwood pads were a shitshow to begin with, needed to be bedded in and the first corner out of the garage the car 'slid forward with full brakes, frightening. Anyway, after they were...

Rounding back on this conversation, I have had mine on the road now and cannot detect any deficiency in either steering or brakes. The hydroboost over the willwoods is great, very firm and...

Finished the hydraulic oil cooler assy today, wired up the fan with external switch. Some would say it was satisfying, nah, another PIA job to get to the end point. Sorted out the air compressor...

Went to mount the ARB lightbar today using the ARB locknuts, after paying the ransom you would think they would actually fit - NOPE, nuts diameter bigger than the slot. So 1 hr on the die grinder,...

Bugger, this just sounds too good to resist.