Was always on the cards, this place is out of control, and very reactive. Lots of delays in baseline data supply, financial release, contract awards processes of 8 months - stupid. I now have a log...
Was always on the cards, this place is out of control, and very reactive. Lots of delays in baseline data supply, financial release, contract awards processes of 8 months - stupid. I now have a log...
Barlows are OUT. Project work collision on site, 3 major activities to execute before August, cant get away. Not happy.
Have been using this for the last 3 yrs on site , especially after the wet when the flies and mozzie population explodes. Used in combination with a fly net and happy days.
They are great, bought one in 1988 and yet to use it in anger apart from rooting around in the backyard testing it. I see yours has a gas bottle - must look at mine to see if it has that flexibility...
I would recommend before application of the anti rust system that you thoroughly wash the area with a rust converter product - plenty on the market - Bunnings have a suitable one, as this will arrest...
Swapped out the Aeroflow Lift Pump to the carter Black today, was a journey of differences, but 4 hrs later all done with new mounting configuration. I have heard a lot of people saying the carter...
The beast is home with the canopy on, thanks to MB and his trusty shed and tractor. Boost pump developed a faultand essentially stopped the car, think I will be looking at a different make, the...
Oh shit, he has started again, god help us! OK what does that mean in plain english please????ps see ya tomorrow at 9
I used to do the dealer servicing run, simply made best use of my time and effort until I found they were using 1st year apprentices and not completing the scope of the schedule and charging me for...
@MB, have a look at these clamps as an alternative. The unit you used is heavy duty for sure, the link below has a distinct difference in that it has a spring effect that compensates for the...
A few of us, led by MudRunnerTD, have utilised old rear seat frames that mount to the existing points in the car, then put the plate you show welded to the frame. This gives you an air gap under the...
Getting closer, inch by inch. Ran the big wire down to the back today, sheathed it in 3/4" heater hose for mechanical protection, spent a good 2 hrs resolving a potential hot spot where Brunswick...
John, the Willwood pads were a shitshow to begin with, needed to be bedded in and the first corner out of the garage the car 'slid forward with full brakes, frightening. Anyway, after they were...
Rounding back on this conversation, I have had mine on the road now and cannot detect any deficiency in either steering or brakes. The hydroboost over the willwoods is great, very firm and...
Finished the hydraulic oil cooler assy today, wired up the fan with external switch. Some would say it was satisfying, nah, another PIA job to get to the end point. Sorted out the air compressor...
Went to mount the ARB lightbar today using the ARB locknuts, after paying the ransom you would think they would actually fit - NOPE, nuts diameter bigger than the slot. So 1 hr on the die grinder,...
Bugger, this just sounds too good to resist.
Fitted the hydraulic hoses for the winches thru the air fed cooler, another fiddly tight as hell job done and dusted. Struggling with the effects of going onto blood thinners and every knock and...
Happy birthday meathead!
Bit the bullet and went positive displacement gear pump for the interchiller secondary pump, mentioned in the advert they are not quiet, however it cant be any louder than the blower, the Neighbours...
Time to put that small tray of kitty litter under the bonnet or on the ground under the car I reckon!
Did it come with all the clips and tabs? New or s/h?
Wouldn't it be great to have a shed organised with all that NP gear, at your fingertips, instead of my debacle of a storage system that starts at the floor level and reaches the first shelf purely by...
The guard was in aisle 17 at my spares location - inside his shed! He didn't have to look far, just ask.
Bought some fittings and hose from the guy who supplied me the kit for the front and rear hydraulic winch setup - what a breath of fresh air in a land of crap - effortless, helping, interpreted my...