If it's for your 2008 gu dx this will helphttp://www.nissanpatrol.com.au/forums/showthread.php?10293-Fitting-rear-seats-to-a-DX-patrol-need-a-bit-of-help-Please/page1
If it's for your 2008 gu dx this will helphttp://www.nissanpatrol.com.au/forums/showthread.php?10293-Fitting-rear-seats-to-a-DX-patrol-need-a-bit-of-help-Please/page1
I got one of the diesel smart ones. ...
Hi G
I've fitted the cross country
Yes expensive but I'me happy with the slight improvement in acceleration
so for me worth the cost
regards
Joe
Real good to hear all of you are stoked LOL
P4trol, One of the pieces that bolt to the floor has a washer as part of it, the black one in the pic.
Graham I gernied the belts and they look a lot better.
http://www.ebay.com.au/itm/Manifold-001-complete-Air-compressor-ARB-Endless-Air-TJM-on-board-4wd-pneumatic-/290971558382?pt=AU_Car_Parts_Accessories&hash=item43bf41a1ee
Here an example of whats...
You'll need an air manifold with a one way valve near your compressor.
You should be able to run air tools with what you have in mind.
Pic is of manifold you need not the fittings.
System is no...
I am now ditching that set up in favour of an endless air set up...
I have diagrams somewhere I did when I made my set up... see if I can find them.
This is from 04off, he did me this diagram...
A couple of members here may have the Ute parts you need .
Cuppa rings a bell as he recently fitted bucket seats to his ute,
Might be worth a PM to see if he has anything left over
It will go straight in. The handbrake lever goes between the 2 seats as its a 3/4 seat. You will lose your centre console and the handbrake and gearstick surrounds are different but you could run...
Check out Diesel Smart who are a sponsor here.
I just replaced mine with a fully tigged job.
Highly recommend, one of the cheaper options
going around and warranty as well.
PM them for price...
Between June 2006 and July 2013.
https://www.recalls.gov.au/content/index.phtml/itemId/1051841
JOB DETAILS PRICE QTY/HRS AMOUNT
JOB 3 RECALL R1306 ACCELERATOR PEDAL NO CHARGE
PRT A8002VS41B LEVER COMPLETE-ACCEL 1 NO CHARGE
PRT 18020VS40A BRACKET-ACCEL P 1 NO CHARGE
PRT 24028VV29A...
Get onto Nizzbits mate and order one it takes 3-4 days to get it, although i am northern nsw, they are out of melbourne, i rang nissan and they wanted $550, mine cost $440 plus $20 for the postage,...
grimace
my 08 wagon was doing the same, would drive ok if i put the boot into it, but sitting around 2000 revs in 2nd, 3rd it would surge (traffic driving). also really nasty in low 4. tried all...
Blocking the EGR will help stopping hot exhaust gasses from entering the combustion chambers and will lower EGT’s. It also reduces the chance of the inlet manifold runners becoming restricted by the...
sweet as mate
keep them piccies a comming ....we luv piccies
A bit of care is needed comparing EGT's between vehicles due to sensor placement, however...
500 degrees under load is perfectly normal for a CRD on song under load (ask anyone with an EGT on a...
Grimace, I have an 07 model CRD all standard motor and exhaust. A mate with a DI consistently returns EGTs at least 100C lower than mine, and this would appear to be the case with them all [as...
There is a couple of products on the market, I use a CRC one . About $25 from memory ...
Yep. 31 splines.
Your front axles should have 31 splines.
Crap gets in anyway mate - hubs are not the best "crud avoiders" when it comes to water and the like, so as long as it's not a large hole we're talking about, go for it .. Maybe use some instant...
were abouts are you on the coast mate iam happy to help i have a intercooler pipe with a fitting brazed on ready to go if you like and iam happy to weld ur pyro fitting on
If you're over 1.9mb, then try this link to resize your images:
http://www.nissanpatrol.com.au/forums/showthread.php?1412-Picture-sizes-and-how-to-reduce-the-size.&highlight=resize