OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

Search:

Page 1 of 2 1 2

Search: Search took 1.00 seconds.

  1. Thread: GQ Auto Lock Up

    by ripper
    Replies
    36
    Views
    9,895

    That sounds like a mistake. You don't want to...

    That sounds like a mistake. You don't want to feed power into both of those wires, just the one that goes to the transmission, not to the tcu one.
  2. Thread: GQ Auto Lock Up

    by ripper
    Replies
    36
    Views
    9,895

    No worries GQtdauto, I just know how expensive...

    No worries GQtdauto, I just know how expensive these autos can get if things go wrong with them.

    Can you please start a thread intro'ing yourself here. www.nissanpatrol.com.au-Introductions
    I...
  3. I bought a Flamethrower and couldn't make it...

    I bought a Flamethrower and couldn't make it work. Got a mechanic to tune it after that and he said throw the new one away and keep using the original Bosch one. He reckons they're the only ones...
  4. Replies
    10,451
    Views
    2,141,403

    It was a lot easier than I expected. I drilled...

    It was a lot easier than I expected. I drilled two holes in the front of it, blew out the old oil (which was like thick dark honey), and put 40ml of 30,000 grade silicone oil into it with a syringe....
  5. Thread: Ripper GQ

    by ripper
    Replies
    21
    Views
    7,568

    Our LPG tank is crossways under the back where...

    Our LPG tank is crossways under the back where the original petrol tank was CPOCSM.

    Photos here
    Front
    Front Underneath
    Back
    Back Underneath

    It's a bit slow to fill with ULP on some bowsers,...
  6. Thread: Ripper GQ

    by ripper
    Replies
    21
    Views
    7,568

    Wow, almost 2 years since I updated this thread....

    Wow, almost 2 years since I updated this thread. Most of that time I've just been driving the GQ.
    About 6 months ago I bought a wreck for spares. It's got a really bad body, but a good engine, and...
  7. Thanks. I still think of it as being more Chaz's...

    Thanks. I still think of it as being more Chaz's than mine. It wouldn't have been anywhere near as good without his help.
    I think the WAT one is a lot simpler, but lacks the protection of not...
  8. If you wanted to keep it locked up at the lights,...

    If you wanted to keep it locked up at the lights, you'd hold the switch down while you brake. In general, the momentary is for activating the lock.


    It needs to reach from the brake light switch...
  9. Thanks Acko. No, it stays locked until...

    Thanks Acko.



    No, it stays locked until you use the brakes or manually switch it off. For steep decents you need to hold the momentary switch down while you brake. Because of this, positioning...
  10. Replies
    22
    Views
    7,107

    Our Trol had one like that when we bought it ...

    Our Trol had one like that when we bought it :tease:

    Since then I added a flat one and piggybacked it off the round one, then screwed it onto the bottom of the step.

    A word of warning to...
  11. Replies
    328
    Views
    64,353

    I'll remember that next time you lose a heap of...

    I'll remember that next time you lose a heap of my photos :1087: :tease:
  12. In the end it all worked. Here's the bracket in...

    In the end it all worked. Here's the bracket in place.
    15659

    Here's the relay box screwed to the bracket, and the blue cable across the middle of the picture is the heat shrink with the three...
  13. My GQ manual torque converter lock up system (lotts of photos)

    There's lots of info for GU manual torque converter lock ups, but I haven't seen a step by step write up for a GQ here, so I thought I'd share mine, and knowing that some of the earlier members of...
  14. Replies
    68
    Views
    15,500

    I've written up the story at the end of my old...

    I've written up the story at the end of my old thread here, but I'm happy to give more details if you want them.
    Anyone rewired a rev sensor in a GQ automatic?


    It went to a solenoid on the...
  15. Replies
    15
    Views
    4,670

    Well I never got to test if my rewiring of the...

    Well I never got to test if my rewiring of the rev sensor worked, because it turned out the box had other massive problems.

    I hope the saga of our automatic is finally over.

    I'll share the...
  16. Replies
    4
    Views
    1,856

    That's sort of what I saw with ours. They have a...

    That's sort of what I saw with ours. They have a ridge across them with a flat patch on both sides of it.
    The reground one has a smooth curve across the face of it. I'm guessing that curve would...
  17. Replies
    4
    Views
    1,856

    Not sure about a lot of that, but I know our...

    Not sure about a lot of that, but I know our rockers need regrinding.
    I thought they were OK until I had to get one done, and then I compared it to the others and realised they all need doing.
    ...
  18. Replies
    43
    Views
    27,814

    Thanks guys. Gotta go to the wreckers tomorrow to...

    Thanks guys. Gotta go to the wreckers tomorrow to find another steering wheel, and this thread had just what I needed to know.
  19. Thread: Ripper GQ

    by ripper
    Replies
    21
    Views
    7,568

    Well today was a fun day. I took the transfer...

    Well today was a fun day. I took the transfer case out (and didn't die :-)

    Broke one of my spanners before I even got the first tail shaft off, so I wasn't sure how the rest of it was going to go....
  20. Rewiring the thermo fans in the GQ (Lots of photos).

    I've started on my wiring projects for our Trol, and thought I'd write them up in case anyone is interested in doing the same.

    Did this job first because I thought it would be quick and easy.

    I...
  21. I only know a little bit about fuel gauges, and...

    I only know a little bit about fuel gauges, and having it work backwards doesn't mean anything to me.

    Not sure if this is safe with an EFI model, so user beware.
    You might be able to isolate...
  22. Replies
    14
    Views
    7,569

    I'll get some photos next time I have the door...

    I'll get some photos next time I have the door trim off.
    It's not just the motors which are aftermarket, the original regulators have been chucked away and replaced.
    There's a vertical channel...
  23. Replies
    28
    Views
    34,325

    That's an awesome site Ross. I just discovered...

    That's an awesome site Ross.
    I just discovered Drifta kitchens. Unreal.
    www.google.com.au/images drifta kitchen

    EDIT

    Here's a slide on, fold out, pop top :-)...
  24. Replies
    28
    Views
    34,325

    Still can't find the one I saw before. These may...

    Still can't find the one I saw before. These may give you some ideas.

    Some of this looks great.
    http://www.travelander.com.au/products/trayback-camper

    One here....
  25. Replies
    28
    Views
    34,325

    DX Grunt has an ex-Telstra pod canopy with some...

    DX Grunt has an ex-Telstra pod canopy with some gear in it.
    http://www.nissanpatrol.com.au/forumsDX-grunt...-in-the-flesh

    I've seen a great set up somewhere but can't find it now.
    Can you get...
Results 1 to 25 of 36
Page 1 of 2 1 2