OUR VIDEOS GALLERY MEMBER SPONSORSHIP VENDOR SPONSORSHIP

Search:

Page 1 of 3 1 2 3

Search: Search took 1.00 seconds.

  1. Thread: All Things Chev

    by MB
    Replies
    1,339
    Views
    457,765

    Sticky: A better radius bend bottom pipework setup would...

    A better radius bend bottom pipework setup would have been nicer though if done again!


    Sent from my iPhone using Tapatalk
  2. Thread: All Things Chev

    by MB
    Replies
    1,339
    Views
    457,765

    Sticky: FWIW mine came with an alloy from previous owner...

    FWIW mine came with an alloy from previous owner (unknown brand) and kept falling apart on the local rough roads. Changed to a local brass for over say 4 years now without issue and are comfortable...
  3. Replies
    1,339
    Views
    457,765

    Sticky: Yes it was through BD cost was $1545, my builder...

    Yes it was through BD cost was $1545, my builder recommended the ADRAD also.
    Project P400 is not on the road yet, will get update this week. Has been slow mainly due to commitments on both sides.
  4. Thread: All Things Chev

    by PeeBee
    Replies
    1,339
    Views
    457,765

    Sticky: Their radiators are brass. My conversion was done...

    Their radiators are brass. My conversion was done 15 mnths ago. They did not offer me an alloy one.
  5. Replies
    10,451
    Views
    2,142,100

    Well my passenger window came off the rails...

    Well my passenger window came off the rails yesterday, hence having to rip the door apart to see whats up. I fixed it and then decided to do all the doors. Those nissan plug things suck.
  6. Replies
    5,631
    Views
    1,168,898

    I once tried browsing that site and had no luck,...

    I once tried browsing that site and had no luck, but the other day I put a part number of one of the parts I was after into google and that website popped up, showing the appropriate section for my...
  7. Replies
    10
    Views
    2,921

    Hi Ian2011. I have the mirror type camera and...

    Hi Ian2011. I have the mirror type camera and have power to the camera only when reverse is selected . I have tinted windows and the rear side windows are blocked out with the silver foil stuff also...
  8. Replies
    48
    Views
    6,819

    I bought a set of lock nuts ...the same as for...

    I bought a set of lock nuts ...the same as for driving lights...I drilled out and used 8mm bolts with hex heads...still have to get stainless bolts yet because the black ones rust as you can...
  9. Replies
    48
    Views
    6,819

    If the bolts are big enough I'd drill and roll...

    If the bolts are big enough I'd drill and roll pin..
    Could also drill a hole in one of the fins and use steel fishing trace and a solid crimp and tie it onto the bar..
  10. Thread: Lightbar security

    by AB
    Replies
    48
    Views
    6,819

    Like these ones? This is what I have used all...

    Like these ones?

    This is what I have used all over my car. We use them in the playground industry.
  11. Replies
    48
    Views
    6,819

    Yes this could work if you use the high strength...

    Yes this could work if you use the high strength retaining compound it would make disassembly quite difficult.
  12. Replies
    48
    Views
    6,819

    There is an anti tamper torx style which requires...

    There is an anti tamper torx style which requires a slightly different tool. The difference being the tool has a hole drilled in the centre of the torx and the bolt head has a pin so standard torx...
  13. Thread: Lightbar security

    by AB
    Replies
    48
    Views
    6,819

    I normally use torx on majority of accessories...

    I normally use torx on majority of accessories but decided to burr the threads but a lot of light bars can be undone from the sides aswell where they pivot so consider that too.
  14. Replies
    48
    Views
    6,819

    You can get security bolts as well which are...

    You can get security bolts as well which are similar to a torx head in place of the Allen key. You can also get bolts that can only be done up and with a specific tool if you don't mind having to cut...
  15. Replies
    48
    Views
    6,819

    Loctite the screws then burr the thread, only way...

    Loctite the screws then burr the thread, only way to get them off is to cut them off
  16. Replies
    48
    Views
    6,819

    Try using torx heads on your bolts

    Try using torx heads on your bolts
  17. Replies
    3
    Views
    1,223

    Have a read of this thread. ...

    Have a read of this thread. http://www.nissanpatrol.com.au/forums/showthread.php?t=21135 This is the bit you want anyway. Here is the BFG pricing: Here are the BFG KM2 prices and...
  18. Replies
    3
    Views
    1,223

    I don't know about Ozzy tyres but I can say avoid...

    I don't know about Ozzy tyres but I can say avoid a mob called huntsman.
    I called about a set of rims, they were in stock so ordered and paid over the phone.

    Many calls and 6 weeks later they...
  19. Thread: All Things Chev

    by PMC
    Replies
    1,339
    Views
    457,765

    Sticky: G'evening lads, A good source of info on the...

    G'evening lads,

    A good source of info on the Chev V8 diesels are the following books;

    1. Corky Bell's book Maximum Boost (designing,testing and installing turbocharger systems!) This is a must...
  20. Replies
    2
    Views
    1,654

    The Mobil delvac is a better oil than the Castrol...

    The Mobil delvac is a better oil than the Castrol but for the ole clunker most of the modern diesel oils should suffice.
  21. Replies
    2
    Views
    1,654

    Hi Ian, only just saw this thread. I was...

    Hi Ian, only just saw this thread.

    I was initially running the Mobil Delvac same as you but changed to the Valvoline Super Diesel because it was easier to get from Supa Cheap in the 20litre drums....
  22. Replies
    19
    Views
    10,313

    Now who is pushing some luck, LOL here ==>

    Now who is pushing some luck, LOL
    here ==>
  23. Replies
    19
    Views
    10,313

    Here ya go ==>

    Here ya go ==>
  24. Replies
    19
    Views
    10,313

    The controller serves a few purposes, the main...

    The controller serves a few purposes, the main two being...

    It won't let you overfill the main tank if there is more fuel in the sub than space in the main.
    and
    It tests that the pump will...
  25. I have the Autron fitted and one of the must do...

    I have the Autron fitted and one of the must do mods IMO. love it
Results 1 to 25 of 52
Page 1 of 3 1 2 3