Good job. You were going to be up for $ one way or another. Rolled the dice and came up 7s haha
Good job. You were going to be up for $ one way or another. Rolled the dice and came up 7s haha
Not that I recommend it.. But I bent mine to get the room I needed. I only ran a 3in though, so it didn't need to move as far as that I think mine just needed a little wriggle room.. Not the 2in it...
I have just gone thru a similar issue, not the same connections, however if you go to a dedicated a/c shop instead of an auto elec you might get a better result. My local a/c shop is absolutely...
bring on the ute thread mate,been through the washer of late by the sounds of it,be good to see ya next car and build thread
Then you can come for a wheel at the glasshouse :)
One point I will make is my vid I am going to fast! It was my first time up hilux hill and was the only vehicle there. So being a bit nervous and not wanting to get stuck I kept the boot in....
Hey Jono. My set up is different to yours as I run 285/75r16s and it's a 4.5l petrol auto. I do have a 63% reduction.
At 100kmh I'm only doing about 1800 rpms. Anyway for me the 63s are just what I...
There is alot of rock in your area, if you dont mind crawlin over rocks in 1st low at slower than walking pace, if you like momentum over tractor dont get 85%
If you like wet slippery hillclimbs,...
Check you tube
Leck48 doing big red I think has 85%
Flex gq doing big red has 63%
Rob doing hilux hill is me with 63%
And I bet is still a sad day as the GQ is fair superior then the GU *L*
They will fit fine. I have a set out if a 60 series in my GUIV. The drawers are all the same, it's just the side panel "fitting kit" that changes from car to car. I had to trim about 20mm off each of...
I'm about to fit this one and add some Toyota silicone oil to my TD42T hub.
This is the fan used on the Infiniti G35
...
Pretty sure 4x4 concepts are the ony ones going atm.
I have the early version of their dual pillar pod, i s
shifted my cruise control light .
there are some very nice dash pod to house a few...
Because I make front recovery points I thought that captive thread would be handy for the GU's with the 4.2 diesel motor
but it wasn't to be, went another route and more than happy with the result,...
You just need to look at the captive thread on the shipping tie down point
on the front.
For something thats welded by a robot on a jig its a long way off
Years ago I made some spacers for my g/box crossmember. I used the passenger side of the chassis to make template and I used 10mm plate. So I tacked 2 pieces of 10mm plate together and stuck it in a...
That's what happen when you downgrade from an awesome GQ 2 a GU :)
I believe what he is saying is if for example you done a 4inch lift and are going in to get that certified, and you have put 35's on and haven't listed that as part of your certification then you...
No worries mate I was just trying to find a cheap and easy way for you to do it.
The Nismo device would only be a resistor. What that value of that resistor is I don't know. As part of the SRS...
It is his choice Bob, I am sure that he knows this and has weighed up the risks............there is really no need for some of the comments that were posted mate
We are not here to criticise...
OK everyone, Jono has asked a question and it is up to him what he wants to do....this is not a place for having a go at him about his decision
Thanks
we're all getting free airbags anyway, the std wheel isnt that bad. to look at.
Could do what Mudski did and have it leather bound, looks the goods.
When I was involved with Holdens and customers wanted their factory seats replaced (that had seat belt pre-tensioner fitted) with aftermarket seats, a dummy load was fitted into the connector for the...
Hey Lucas, yeah I used to work there. was dannys old patrol. Was a pretty extreme short trip but we both worked well together to get ourselves out of trouble and i cant recommend that tigerz11 winch...