Search:

Qwik piks of the air install on mine.
Runs off the A/C pulley (obviously)
Only issue is that it is goddam hot down there under the A/C
Soooo... I'm thinking of sourcing cooler air somehow

Have removed now the stock PS coolers and stock lines that were in my way for new oil coolers. http://www.nissanpatrol.com.au/forums/images/imported/2017/11/36.jpg The new Davies Craig Hydro Cool for...

Kindly received some pics today from http://www.blitsbodykits.com.au/ for the GU Supercharger bonnets if anyone needs raised rainsey Cheers mate!
I believe this one below is for GU4 and onwards:...

much prefer this one with built in intercooler.
73312

Some of those P400 pics are screaming "supercharger bolts on here" to me...

All done mate...

http://nissanpatrol.com.au/9-2815-237-34.pdf

Here are some more pics. the last one shows the bed plate of the P400.

731977319873199

Believe it or not, this is a P400
And I specifically said, no vac pump too......

73195
73196

Hmm, I spoke to Greg on Wednesday and talking about my heating issues and he indicated that he was removing the viscous coupling from many vehicles as he had a machined adapter that brought the fan...

Hi Mark I have spoken to Scottie at BD and explained the temps I have experienced - he said BD are getting some "new" viscous fan hubs - apparently lock up better to provide more air flow. Waiting...

G'day Phil, I'm by no means an expert on these donks sorry mate, just learning my way through them too to make mine hopefully bulletproof. Here is the page photo again from the US military full...

Good little article here for you guys with overheating issues before you chop your cars up
http://www.autospeed.com/cms/article.html?&title=Undertrays-Spoilers-Bonnet-Vents-Part-1&A=113176

I used 45 deg and stright hoses and pipe in between I have had the 4" snorkel from the start so can't comment on any performance gains

Kimbo, how did you get them 'pre-moulded'? By that I am assuming they were moulded with the bends/changes or directions?

Have you had the 4" Millweld snorkle since new or changed from a plastic...

Sorry 131-103 :-(

http://catalog.autobarn.net/ShopByVehicle.epc?q=2001-GMC-Van--G1500--1/2--Ton--Savana-V8--395ci--6.5l--Diesel--Turbo--Vin--F-Belts/hoses/cooling&yearid=2001%40%402001&makeid=31%40%40GMC%40%40T&modelid...

Made a quick video for you mate that may be helpful.
https://vimeo.com/202574268
The Yanky 88's currently installed outperform the originally installed Aussie 82's by miles. I've done each cooling...

Hey mate just seen this have been busy working and no time to get on the net
I think my truck runs cool due to good air flow my front bar is very open and offers no restriction to air flow also I...

this image shows simplistic airflow, underbody is considered low pressure

70810

Running lean will make things cooler in a diesel.

Lower twmp thermostats wont reduce your under bonnet temps. 2 extra cylinders pumping out heat will bring them up. I would be more inclined to be...

Ha,

Thunderbird 2.


Sent from my iPad using Tapatalk HD

OK, back at square 1 again. Sump replaced, springs replaced, alternator replaced, added new Safebrake brake lines, hydraulic winch sorted and operational, working on mounting the additional 200a...

Check with mudrunner he fitted a y62 fan blade to his gu, not sure it will fit the Gq but he says it looks very similar to the Ufi fan

Hi there! Been away from this site for a while, and have since updated from a TD GQ to a TD GU, not a bad rig but old mate severely understated the overheating issue, the engine is fine, no evidence...

Welcome!!!