next time lay the tyre on the floor and hose it so all the bead has water pooling on it and you will see bubbles if it is the bead.
you can use a high lift jack or tyre bead breaker or just drive...
next time lay the tyre on the floor and hose it so all the bead has water pooling on it and you will see bubbles if it is the bead.
you can use a high lift jack or tyre bead breaker or just drive...
here are some pics of my idea i came up with. pretty simple and works great
Righto a lil bit of history.
Its an ex telstra ute that i picked up last august. since getting it i've done a fair bit of work
2" dobinson lift
3" exhaust with dump pipe from turbo
Pyro+EGT...
I thought they bolted on but the Pitman Arm and the tie rod tapers were different between GQ and GU steering assy's so you needed a GU tie rod end to match the taper and/or adjustable draglink to set...
Straight bolt on mate - did it myself when I was in Melbourne with the lads at Christmas .. took Patch and I a bit longer due to getting the banjo fittings back on, but a straight fit none the less...
thats gotta suck, at least you found the reason and the boys are helping you out
if there is no screw underneath or they do not twist apart, they will be sealed (supposedly) which means throw em in the bin or send them back for a refund.
If they are sealed, once you break the...
How long have you owned them mate? were they turned on when you went in the water/mud? If they were on then a Hot light can cause a vacuum when entering cold water. If they were turned off then they...
is there a small screw on the bottom side of the chrome ring ?
undo that, pull bottom of the ring out a bit then unhook tab at the top to lift off. ???
There's Androzic for android I've downloaded it but have yet to learn to use it properly.
there is a lever next to the the driver seat. if you dont have one you need to buy disconnects from superior engineering. you need to get under the car to disconnect them. as good as they are I found...
Should all be on the website mate ...
I've still got to register!!! lol - with the truck the way it's been, I'm un retain if it'll be ready for competing ...
Thought this could do with It's own thread so everyone can see it.
MudrunnerTD was on 4WDTV lastnight for the My Rig segment and we managed to get the video for those who missed it.
Thanks to...
Shows have already started guys.
Sundays @ 3:30pm or Tuesday's at 8pm on TV4ME.
I'm just waiting on the past episodes to get sent to me which shouldn't be too long and we can also watch them on...
Wow a dhuck that dont like mud n water hahahahhahahahahahaha
Ahhh, the owners manual... That is the one with the dealer stamps in it for all the services? That manual normally disappears when the 1st owner sells it... :1087:
Sorry, can't help. Never seen...
Beware Ankle Splash !!!! :-)
auto... From memory, it's a 9323 auto.
I've changed computers and all the info's on the other one.
This was sent to me today and it was too good not to pass on.
Tony
Engineering solution
(You don’t have to be an engineer to appreciate this story but it helps !!!! )
I have some great news folks!
I'm seeing Simon Christie from 4WDTV on Friday for a "My Rig" segment and a small little mention on their show about the forum which will hopefully bring us a lot...
The rails and also there are 2 drain hole in the window from memory. They can block up then water gets into the welded window pinch seems and starts rust around the bottom of the rear window under...
Here tis ... nothing too flash as it was all from the in car camera (I detached it for some outside footage also) ... enjoy ...
http://www.youtube.com/watch?v=AgcRza1o30U
Nice find Andy...LMAO how about getting someone in a NISSANPATROL com advertising board with a mega phone out side the largest Toyota dealer near them or even at a toyota 4x4 club outing...sprouking,...
She's pretty tough mate. i did mine well into the 300s. If your concerned you could get a compression test done to confirm engine condition....But.....HELL YEAH!! They love it. I think that they get...
Hmmmm .... naahhh ... I'm going with the 'burn in hell' guy ...
Now hang on, and hear me out ...
Had I have just got on here to download the manual (and gotten it for nothing) then just like...