These anti-recoil straps from a manufacturer over here in Perth might save a few lives. This would at least dampen the force somewhat if the strap breaks near the eye or a connection comes adrift...
These anti-recoil straps from a manufacturer over here in Perth might save a few lives. This would at least dampen the force somewhat if the strap breaks near the eye or a connection comes adrift...
https://www.redarc.com.au/vehicle-management-systems/tvms
Sent from my SM-G935F using Tapatalk
Link to this YouTube vid showed up in my email today. Thought a few of you might enjoy it.
https://www.youtube.com/watch?v=aWeZTfx4lGg&feature=em-subs_digest
Drive both, and see what you prefer.
2008 is CRD, so I would jump on one of these if that is what you are after. They are incredibly capable, go anywhere, and don't seem to have the inherent...
If anyone is over this side, i have found Perth Powder Coaters in Fairbrother St, Belmont excellent value for cash jobs. Just make sure you have correct cash as they don't do change, $40 job became...
73699 the only pic i have at the moment, 7.3 turbo diesel.
Mine didn't have an antenna like that but had numerous wires throughout that were no longer connected to anything. There are probably still some hidden away but I, like DX Grunt binned as much as I...
Here's the link
http://www.transport.wa.gov.au/mediaFiles/licensing/LBU_VS_IB_132.pdf
Take care out there.
Rossco
I'm meeting up with Len next Monday or Tuesday week, and looking forward to it.
Rossco
I have 3 'Reese points' or 2 inch receivers on my truck;
- the Tow Bar obviously,
- a custom jobbie made by XLR8 in Perth (that bolts to the rear chassis cross member where the factory recovery...
Nah, mostly it's just get too old n have to dumb down! :rolleyes:
And welcome back Len
Well done! We all grow up and move to a GU at some stage in our lives :)
Welcome back mate
Welcome back to the forum mate.
Welcome back mate and congrats on the new beast!
Ask Rossco about how much he loves Toyota's next time you see him too lol
Sent from my iPhone using Tapatalk
Hi Greg, have you thought of attaching a 2kg unit to the front of your seat, Or even attaching 1kg units to both front seats if room is a issue. I had this set up back when I had my Torana and was...
1. find a steel pole at work thats not being used that will house the shovel
2. cut said pole to length required
3. bur of the ends so it wont damage the handle
4. find some nuts and bolts around...
prep for top coat/s.
1) 7-900 wet n dry smooth blend edges.
2) dust off, wax n grease clean again.
3) tape top edge gutter and to lower edge of ridge and if metallic also top of ridge....
remove gutter end caps if you have em.
1) clean scrub out gutter to remove all foreign substances incl wax & grease to clean.
2) cover entire car help to keep dust and sand out of places you...
Recently repaired gutters as paint was peeling and needs repair.
Before gutter rust started to take hold.
This is for the inside part of the gutter, can't really see just standing beside car, not...
Hi Guys,
This thread has been going for some time now. So thought I'd put a little input of my own. As one of the previous posters quoted, if the deep cycle is being used to start, they certainly...
I should have been a little more descriptive & said I sprayed the moving parts with dry lube & not the internals of the motor itself.
Cheers Benny & top tips to mate.
I had a similar issue & found that dust had got into every part of the wiper assembly & after a removal rigorous cleaning & a good spay with dir lube it was all good again.
Its not a fun job but...
Hey mate - the wiper motors have a tendency to die and are fairly cheap and easy to replace - I'd suggest checking the wiring from the motors first, but if no obvious signs or issues, then possibly...
Yes, this would be rust converter. Once the chemical reaction has finished it usually turns a blackish colour.
Rust converter is an excellent way of dealing with rust as long as any loose scale is...