Finally connected the electrical feed to the bank of lithium's in the pod, turned on the 10Kw inverter and plugged in the 240V 15amp lunchbox welder, ran it at 100amps for about 3 mins continuous and...
Finally connected the electrical feed to the bank of lithium's in the pod, turned on the 10Kw inverter and plugged in the 240V 15amp lunchbox welder, ran it at 100amps for about 3 mins continuous and...
Here is the image I have tried to attach 2 Million times 88064
Crap it works now, or great work!
This is the new tapping wrench above the older 'still in service heavy duty wrench I made in the...
This brute arrived today. The original surviving HD tapping wrench is at the bottom. I like the extra leverage and everything is so much bigger and gruntier.
88037
The forum fired up fine this morning on my laptop pc.
Update on the Codan 'death Bracket', now modified.
88034
Getting database error on desktop but iPad opens up fine @AB
If they will supply a replacement, I am happy to pick it up and post it to you, only 20 mins from me, not a problem.
I believe it helps the vehicle to run.
Work is getting intense and chaotic. Simply cant get away, PIA in all honesty.
I think you should be able to get dimensional information from Doctor Google.
Yes I hold an amateur operator licence, but dont spend time on the service, its more for peace of mind contact if I ever need to get out of a jam. The HF service this radio works on has maybe a...
Bought a new h/d Sutton Tapping wrench, finally destroyed 3 wrenches today in fast succession on the tapped holes of the antenna mount - poor man pays twice comes to mind! Also bought a set of the...
Bit more progress, chest infection, again, holding me back, but baby steps get the job done. Finished the pivot mount for the big antenna, then trial fitted the new TRED boxes, ordered another 65L...
What are you expecting or wanting to get from the tank and pump? Are you looking to fill a pot or use it for a quick shower or wash mud from a clogged radiator? I think this is the starting point in...
Started and completed a pivot bracket for the Codan HF. Allows transport position at 30 deg tilt so it does not get clobbered from trees and branches, then undo 3 bolts and stand it upright with the...
Looking good Mark. I had my staino 4" powder coated, came up really good if you want the black look
Here you go
https://www.marks4wd.com/low-range-overdrive-gears
Its a HF radio, a box full of electronic boards. The antenna is the transmission site and at 100w at 8ft off the ground,1500mm away on the rear of the pod, nothing of any concern. There are no gamma...
Looks good, the extra pipe length would add restrictions in the order of 4 decimal places - not an issue, clever about the drop end to keep the water out. I have never had a problem with my forward...
OK, so the UHF radio goes in the POD as well? I don't think you really thought that comment thru. Maybe i should put the water tank back there as well to save on tire wear on the front wheels? The...
Mark, I have this conversion and I am now sitting in the sweet spot for max economy at 110klm/hr at 1750rpm.Unlike the 85% reduction gears that howl all day in low range the machine finish is...
Its a mounting bracket for a Codan HF radio. Its mostly behind the headrest, but i am going to chamfer the stiffeners to take away the sharp corner - funny what you dont see when you are making it....
Fabricated another custom bracket to mount the Codan HF radio, time consuming and converting ideas into reality - came out well, mounted above the SS water tank behind the rear seat...
Got the rear pod wired 95% today, power to lights, inverter, DCDC, fridge, exhaust fans on thermostats, just need to do the penetration to get the charge cable into the pod - maybe tomorrow. Lights...
I think this refers to the diaphragm valve inside the pump so it sucks in liquid and the valve closes then the diaphragm discharges against the closed seal, pretty normal, there will be a flow arrow...