Peter, yeah it definitely wobbled on the way home from BJs.
I regreased the bearings. They had plenty there already though. Maybe it was a flat spot.
Joe, it certainly would have helped to...
Peter, yeah it definitely wobbled on the way home from BJs.
I regreased the bearings. They had plenty there already though. Maybe it was a flat spot.
Joe, it certainly would have helped to...
Auto one sells a complete aerial kit, i got mine sitting next to my uhf antenna ,,
easy to install
As most of you know we have upgraded to a new software.
This new software enables us to have our own mobile version of the forum that we have full control of.
Next week I will be playing around...
Thicker cable is the way to go. 1.5 metres is not much of an issue, but remember you have to double the distance to account for negative & positive. (Total length). Check out the table at the bottom...
With you future plans the dc to dc without doubt. If you fit an isolator (VSR - Voltage Sensitive Relay) now, there will come a time when you realise that that you are not fully charging your...
came across this a wile back. Could be useful.
TAKE NOTICE
My vehicle/trailer is roadworthy and registered.
Its current location complies with road traffic rules and regulations. At present I...
Well Cuppa I have taken a while to read and digest your posts and those of our fellows.
I am not at all surprised by the attitude of the RV mob that are lobbying for their exclusivity.
We wanted to...
WARNING: This will be a very long post, but I assume that many who love 4wd's also love to camp, be it with a tent, camper trailer or caravan & thus it will be of interest.
On another forum I have...
This is a fascinating topic, and there are quite a few threads on here - I use the search function rather than wait for people to send a new response. Make a cuppa and put the feet up is my advice...
Gday JoeG, all auto cable has always been identified and sold as the total diameter which doesn't really help as some of them have thicker insulation and dont relate to the actual copper conductor...
I found a great mechanic that had come across the same problem before with the ZD30 engines, problem has been fixed with some silicon and I was told that is all Nissan do as there are no gaskets used...
The remote head for my GME 3520 is mounted below the heater controls, the main body of the radio is mounted under the passengers seat. The remote head was in the way of the subtank switch (which was...
Well got it worked out it was the pan hard bushes. All good now. thanks for your help.
Go genuine with the pan hard rod bushes too mate, the after market ones don't seem to last to well.
Try this bloke & tell him your from the forum.
...
nice jobs.. looks good
I moved your post into the DIY section mate as this is a good DIY job for those who like to modify.
I did a quick Google search and found that 4WD Systems sell them, and I also read a while back that Enzed were selling them. I got mine from Berrima Diesel about 8 years ago.
Can't see why you...
I have bought about 12 of these for mine and friends cars and they are very bright, to the point where it hurts when the mrs flicks on the map reader lol. Comes with all the attachments and fits the...
Hi,
One from the MG nut but I know you guys with all the extra boxes might appreciate even if you've got more room than me.
How to change the oil in your Gbox, Dif etc the easy way.
(Not a...
After lining up with above mentioned referenced point, I am using a tie-down strap and my 12 volt pump to reseat the bead, just to make sure I can do the same in the bush. It seated far easier than I...
Feel Free to post away now.
Thanks for being patient.
To my knowledge this is the best way to join two snatch straps as it shares the load equally between the two loops.
Tony
http://www.nissanpatrol.com.au/forums/images/imported/2011/04/1.jpgA nutsert works on the same principal as a pop rivet.
...
Some more pics of the job.
In order:
1. The main shaft stripped and set out on the bench.
2. The gear box housing after a good bit of cleaning and recoating.
3. All the shafts re-assembled and...
Scangauge is the OBDii compliant display so works on CRDs and nothing else Patrols wise... ECU Talk works on the other models
http://www.scangauge.com.au/
Being OBDii I can use it on all the...