Search:

been having troubles with my y61 sliping teeth inside front free wheeling hubs so i replaced them on to chew the new ones out in about 3 hours. thinking it was somthing major turns out some after...

39667

Dredger - Porcupine Flats Vic.

There is an easy fix for this as Ni$$an wants you to buy new lid for $275 or so.
Just visit CBC Bearings establishment and get "O" part number BS445A.
Fits like a glove is made of rubber and it...

Old cart outside Peterborough

G'day folks,

I cannot get over the customer service from overseas v local customer service! I recently purchased turbo stainless steel T/Bolt flanges, aluminum inter-cooling piping and silicone...

Okay. The issue I had was when I wound the window up it was going back down a few inches by itself after it reached the top. What I did to fix it was to remove the motor from the reg, plug the reg...

I agree with Yendor, and think it has something to do with the Limit Switch being out of whack.

34131

Here is the reset button for the window limit switch

Gday, recently had same prob n flashing on/off int light coz of door. Used impact driver to untension U plates, tapped em inwards with hammer, slam doors, retension.
Problem solved, can even notice...

Careful naming and shaming..... I am all for it myself!!!

G'day Clunk,

Well stated mate and so true, there is definitely those customer's out there that constantly whinge for the sake of complaining!

On the weekend in Coffs Harbour there was a...

Very well put RLI but there is a but and that but is the customer who makes unreasonable demands, ones that are unfortunately not possible to fulfil.
Now before anyone pipes up, I'm not saying...

G'day Trendsetters,

Another one of my pet hates, is businesses that are so arrogant (that far up themselves) and because they think they have a good product, they think they can treat there...

Kast, I would not recommend any brand or model of a brand as all our needs are different.

The high end Konis are supposed to be the best for outback rough tracks but how do the perform in the bush...

Well not me exactly...


Blokes, my misses is finally preggers!!!

It has taken 12 months and I was completely over it and lost hope, lots of crap times around our house in the last few...

AB I move we lock the Manuals section up and access to forum sponsors only. Let it be seen by all but access to the links requires a 12 month sponsorship. $20 is pretty cheap for ALL OF THE MANUALS

Thanks for the reminder Grunt!

Got sick of Motorculture so gone back to Tappa

King Springs (lifetime warranty) and KYB shocks - they are OEM suppliers to a lot of jap trucks (3 yr/70k warranty) all for about $700. if you can use a spanner fitting is a piece of p*ss. Took me...

10 day Ban for first offence. Permanent Ban for second.

Happy Days!

If you have a Budget of $1500 not including fitting then your looking in the higher end of the Market. Happy days.

You could go all out and fit Superiors Amadas remote res shocks and springs for...

Heres where I got my gauge from...

http://www.mcnallyelectronics.com/

Here ya!.Sitting in the drivers seat you can still see all of the tacho and speedo, just not in that pic.

Its not that daunting mate, the rear discs pretty much fall off. You can remove the caliper and cradle in 1 piece with the pads still in there so you only remove 2 bolts or remove the caliper then...

Think he means if only running a boost gauge this is perfect,
but also if Fitting NADS you could TEE into it to pick up the DAWES valve.
Makes sense
Edit The more I look at this product and the...

Can't say I'm a fan of digital gauges, just for the flickering effect.
They look ok price is ok too.
Most here are running STD 52mm round gauges, either on a pillar or dash pod
one or two run two...

Sure. Regardless though if its. Positive switch or a negative switch the diagram will work. The function will work anyway. Make the whole lot positive or negative. Your choice.

Reading th first...