All of the above run through your clock spring, either snapped the ribbon cable inside or the plug fell off the back
All of the above run through your clock spring, either snapped the ribbon cable inside or the plug fell off the back
Hey Peeps,
Been a while since I was last on here but I have finally had time to get into swapping out my split in half TD with a fresh LS3:
Things to note - Waiting on radius to get airbox etc...
Oo and if you habe a coolant leak into combustion chamber and burn you will find that it shall actuall clean the plugs. Same deal as water meth and also just pouring water into it when its runnig...
Unfortantly thats a complete negative. Without going to deep into the actual chemical science it cant be and never has been red oxide.
Only things that make a plug look like that are leaded...
Hey, Just a bit of an update!
So up here in lovely Moranbah its Hot ASF! :) Perfect to test everything out.
Current setup is same as before except I now have an auto instead of a manual.
Test...
Dodgy hazards switch will do this
Sent from my SM-G935F using Tapatalk
dom14
Trust me I've built many engines from 4cyl through to 12cyl. Im not saying it wont work im saying it wont last.
Here is sorter the point Im making, there is alot more to metal work and...
You will find it isnt reaching the advertised 6k watts. Sorter like those genpower 8kva gensets on ebay for $800 wont even run a small box a/c or start a fridge.
If you want to use a welder with an...
Finally pulled the manual clutch pedal and brake pedals out, in preparation for swapping over to an auto. Poor things needing some attention, spent the last month working on other cars instead. oo...
Not really old school, its pretty common first step check ups :) only pull the tools out when its not an obvious thing, as in porous metals and fine cracks.
Sorry for the very late reply, Heres some pics of the cool, heat exchanger and bar/plate heat exchanger & lines.
Got a bit ahead of myself as all this new power ate the clutch so now im half way...
Ill grab some piccies when i come off shift, (thursday) The actual cooler I still have sitting ontop of the engine, very short path from turbo to manifold. and then an additional radiator in front of...
PeeBee Second coil in front would work but no where near as efficient and very cumbersome. Ambient temps were 32 degrees
nissannewby - Would love to put more fuel in but need to wait for the new...
Easy as one man, Just pull the instrument cluster out and as you look at it its the plug on the far right of the cluster. Light blue wire, and grey wire for earth Cant remember pin numbers off the...
Sooo long story short I went and through another few grand at the patrol in the last month and have walked away quite happy and surprised.
Part of me little shopping spree was an intercooler that...
Drove it haha! First time in months since starting to play with it, could not be any more happier boost response is just stupid 20psi by 1600rpm. My little experiment has worked well, my intake air...
S4 barn door on - just gotta fit the new badge
Kut snake flares on
Started making my custom a/c lines for a lil experiment
Painted the sliders
s3 tail lights in and working
Hopefully the...
Sooo got the dash all back in and everything working a treat, manifold and a/c lines arrived yesterday - A then had a hulk moment when i realized they 1. cut the wrong a/c line and now *** it and 2....
71920
Will get some more pics once the flares are on
Plunger size... think of it like piston bore size.....
Sent from my SM-G935F using Tapatalk
Sometimes you dont have a choice but to do it, but always as a last resort. Normally when you get tyres that have been stored for a long time all stacked up and it squishes the sidewall in. No amount...
Yes.... try booting up with hardware sig disabled. Its a windows 7 and on security thing. Even if its plugged in windows will disable it and shut it down. You have to disable it to let the chip run....
King pin bushes? have you checked them
They will do exactly what is happening to you specially if one is shimmed and one isnt as It puts the knuckle out of square ( makes axle sit hard and top of...
Check your float levels :P
For a carby rb30 for good eco and running you should be around:
Idle- 14:1
Cruise:14.3-16:1 Depending on what your motor can take
WOT:12.8:1
Well its happening again....
Turbo
Cooler
Pump
Water tank
Snorkel
Airbox
Gvm upgrade
Gu4 interior
All on there way and or booked in to do :)